Picture Settings; Forced Settings In Programme Mode; Sound Settings - Toshiba 28H14D Serviceanleitung

4.3.3 Picture Tube Type
Call up the "Tube type" menu via "Info centre" –>
"Installation" –> "Dealer service menu" –> Code number "8500" –>
"Special functions".
Select the appropriate picture tube type.
4.3.4 Hosiden Socket
Call up the "Hosiden socket" menu via "Info centre" –>
"Installation" –> "Dealer service menu" –> Code number "8500" –>
"Special functions".
Select "yes" or "no".
4.3.5 Subwoofer
Call up the "Subwoofer" menu via "Info centre" –> "Installation"
–> "Dealer service menu" –> Code number "8500" –>"Special functions".
Select "yes" or "no".
4.3.6 AGC Setting
Feed in a standard channel raster without finetuning in band 1.
Call up the "AGC setting" menu via "Info centre" –> "Installation" –>
"Dealer service menu" –> Code number "8500" –> "Special functions".
(See Alignment, Point 2).
4.3.7 Clearing the TV-Guide Flash
Call up the "Cancel EPG flash" menu via "Info centre" –> "Installation"
–> "Dealer service menu" –> Code number "8500" –> "Special
functions".
Pressing the "OK" button will clear the TV-Guide Flash.
4.3.8 Teletext Level 2.5 Support
Call up the "Videotext level 2.5" menu via "Info centre" –>
"Installation" –> "Dealer service menu" –> Code number "8500" –>
"Special functions" (to page 2).
Select "yes" or "no".
4.3.9 IF Type
Call up the "IF type " menu via "Info centre" –> "Installation" –> "Dealer
service menu" –> Code number "8500" –> "Special functions" (to
page 2).
After replacing the NVM on the Signal module, it is necessary to adjust
the IF type:
National sets: National
Multi-8 sets: Multi 8
Multi-9 sets: Multi 9
Others
(see Alignment, Point 15).
4.3.10 SAT Preprogramming (only with a SAT module fitted)
Call up the "SAT preprogramming" menu via "Info centre" –>
"Installation" –> "Dealer service menu" –> Code number "8500" –>
"Special functions" (to page 2).
Press "OK" for confirmation. This transfers the stored SAT station table
to the SAT module.
4.3.11 OSD-Layout
Call up the "OSD-Layout" menu via "Info centre" –>
"Installation" –> "Dealer service menu" –> Code number "8500" –>
"Special functions" (to page 2).
Select "red".

5. Sound Settings

Press the "blue" button to call up the "Sound settings" menu.
The settings "Voice", "Music", or manual can be selected in the
"Presettings" menu.
The "manual" setting allows you to adjust the sound to suit your taste.
For the other settings, specific values are preprogrammed.

6. Picture Settings

Press the "red" button to call up the "Picture settings" menu.
In the "Presettings " menu, the settings "During the day", "In the
evening", and "manual" can be selected.
With the "manual" option, you may set the contrast and the picture
sharpness. For the other settings, specific values are preprogrammed.
7. Settings via the Channel Allocation

7.1 Forced Settings in Programme Mode

Call up the "Sound channel" menu via "Info centre" –>
"Programme chart" –> "green button" –> "Change channel settings".
You may select between "autom.", "Mono", "Mono B" and
"Mono C".
Mono B = Original sound track
Mono C = For digital sound reception (Nicam).
1 - 17