Inhaltsverzeichnis
Werbung
6. Bild-Einstellungen
Mit roter Taste das Menü "Bild" aufrufen.
Im Menü "Voreinstellungen" sind die Einstellungen "Am Tag", "Am
Abend" und "manuell" anwählbar.
Die "manuell"-Einstellung lässt eine Regulierung von Kontrast, Schär-
fe zu. In den anderen Einstellungen sind bestimmte Werte fest vorge-
geben.
7. Einstellungen über die Senderbelegung
7.1 Zwangseinstellungen im Programm-Mode
Das Menü "Tonkanal" über "Info-Center" –> "Programmtabelle" –>
"grüne Taste" –> "Kanaleinstellungen ändern" aufrufen.
Sie können zwischen "autom.", "Mono", "Mono B" und "Mono C"
wählen.
Mono B = Orginalton
Mono C = Bei Digitalem Ton-Empfang (Nicam).
Service and Special Functions
Call up the Service Menu:
Call up the dialogue line:
Changing the setting in the dialogue line: Buttons " " or " " –> "OK"
Back to previous menu:
Exit menu:
Dealer service menu
(code number)
1. Switching-on Options
1.1 ATS Reset
Press mains button "ON " while holding down the " " button.
- The basic analogue values are loaded.
- The ATS bit is set. When switching on the next time, this option
releases the ATS euro plus function.
"Language", "Country" and "Programme Chart" remain unchanged.
1.2 ATS Start
Start the Auto Tuning System via "Adjust language on screen" –>
"Adjust country" –> Satellite (optional).
The ATS explores the frequencies in ascending order, indicating the
channels.
When setting the country F and *others, the display mode can be
changed optionally to indicate either the channel or the frequency.
The ATS system determines the channels with station identification and
stores them in the station table, .
A pressure on the "OK" button ends the AT search.The ATS bit is not
reset.
Resetting the ATS bit without changing the existing channel table:
After ending the channel search with "OK", select channel entry in the
channel table, enter the indicated channel again then confirm with
"OK".
After storing this setting, the ATS bit is reset.
1.3 Memory Allocation CIC38091 (SAT module).
- SAT ident, video data, (deviation, H/V), audio frequencies "High" and
"Low"
- SAT ident, Peri, finetuning, channel number
- Audio frequency High/Low, video data (deviation, H/V)
- Luminance, noise, TV standard, text/menu
- Volume fine, sound peak
- Station ident
- LNC frequency
1.4 Electronic Programme Lock (parental lock)
Enter the key sequence "7 0 3 8 5 8 0" to cancel your personal code
number.
1.5 Software Version Number
Call up the
"Info
centre" menu. Pressing the "green" button displays the
software version number of the TV set.
It is possible to load the software via the service interface on the
Feature Module.
1.6 PIP Position (only with PIP module)
Press and hold down the "PIP" button on the remote control while
switching the set on with the mains switch. This activates the PIP
mode.
Adjust the horizontal and vertical position.
Using the Format button, you can change the upper right/left and
bottom right/left PIP position.
Press "OK" to save the position.
Note: It is not possible to display VGA or RGB signals as PIP picture.
1.7 Service Mode Programme (for fault finding on the I
These error messages refer only to interferences on the I
to modules or circuits which do not return an acknowledgement via the
I
2
C bus, e.g. no operating voltage supplied to the module, break in the
2
circuit path, or I
C interface defective.
Button "i"
(Info
centre)
Buttons "P+" or "P-" –> "OK"
"Blue" button
"i" button
"8500"
The existing settings
2
C bus)
2
C bus, that is,
1 - 15
Werbung
Inhaltsverzeichnis
