Herunterladen Diese Seite drucken

Kinderkraft GOSWIFT Bedienungsanleitung Seite 11

Laufrad
Vorschau ausblenden Andere Handbücher für GOSWIFT:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 9
● The person using the product must always wear shoes.
● Assembly must always be carried out by an adult. Before each use, check that the item is not damaged or worn and that
all assembly and fastening parts are in good condition. Ensure that the bolts and nuts retain their auto-locking properties.
Check that the assembly is complete and in good condition. If you notice that some parts are missing or damaged, do
not use the product, but contact your retailer.
● Be careful when riding bicycles, you should know how to ride to avoid falls or collisions that could cause injury to the
user or a third person.
● The safest areas for the persons using the bicycle are those with little or no vehicular traffic, such as private areas,
playgrounds, schoolyards, and school playgrounds.
● This product is intended for a user with a minimum height of 80 cm and a maximum weight of 35 kg.
● Keep the packaging or dispose of it in accordance with local regulations.
● For the safety of children, do not leave parts of the packaging freely accessible (plastic bags, cardboard boxes, etc.). Risk
of suffocation!
● Warning. Not suitable for children under 36 months. Small parts. Choking hazard!
I Bike components
1. Frame with attached seat
2. Handlebar
3. Front fork
4. Wheel x2
5. Seal ring
II Assembly of the bike
Start assembling the bike by fixing the front fork (3.) to the wheel (4.) using the threaded pin (6.), a pin screw (7.), two
bushings (8.) and two Allen keys (9.). To do this, insert the pin through the hole in the frame, then insert the bushing, pass
it through the hole in the wheel, insert the second bushing and screw the pin screw to the pin with the Allen key (FIG. A).
Slide the assembled structure into the frame (1.). Make sure the latch on the top of the front fork is in front of the bike
(FIG. B). Then place the seal ring (5.) and the handlebar (2.) on the top of the front fork, first tilting the safety lever on the
handlebar to facilitate mounting (FIG. C). Close the safety lever once the handlebar is mounted on the fork (FIG. D). To
dismount the handlebar, tilt the safety lever (I), press button (II) as shown in Figure E and pull it out of the front fork. The
rear wheel must be mounted similarly to the front wheel using a threaded pin (6.), pin bolts (7.) and two bushings (8.) (FIG.
F). It is possible to adjust the saddle height using the screw underneath the saddle. To do so, loosen the screw with an Allen
key, adjust the saddle to the correct height and tighten the screw. Note that the symbol indicating the minimum depth of
the insertion of the bracket must be placed inside in the frame (the saddle must be inserted so that the arrow on the
bracket is inside the tube, below the seat clamp) (FIG. G). CAUTION! Before each use, check that all connecting elements
(screws, pins, bushings) are correctly fixed. Keep small parts out of reach of children.
III Maintenance and cleaning, storage
Clean the product with a damp cloth or sponge. Protect from dust, moisture, water, high and very low temperatures, falls,
etc.
IV Warranty
1. All Kinderkraft products are covered by a 24-month warranty. The warranty period begins on the date of releasing the
product to the Buyer.
2. The warranty is valid for products sold in the following countries: France, Spain, Germany, Poland, United Kingdom, Italy.
3. In countries not listed above warranty terms and conditions are determined by the Seller.
4. It is possible to extend the warranty period to 120 months (10 years). Full text of the terms and conditions and warranty
extension registration form are available at
5. The warranty is valid only in the country where the purchase was made.
6. Complaints should be submitted by completing the form available at
7. The warranty shall not cover:
a. claims arising from product specifications, as long as they comply with those specified by the manufacturer in the
instruction manual or other documents of a legislative nature;
b. product damage caused by improper maintenance or use of inadequate chemicals;
c. colour change (discolouration) when the product has been exposed to direct sunlight against the instructions provided
in the instruction manual;
d. tear, wear, crack of fabric/plastic that is the fault of the Customer;
e. reduction in the quality of the product and consumables due to normal wear and tear;
f. products which have not been used according to specifications;
6. Threaded pin x2
7. Pin screw x2
8. Bushings x4
9. Allen key x2
WWW.KINDERKRAFT.COM
11
WWW.RMA.KINDERKRAFT.COM

Werbung

loading