Using The Memory Function; Factory Settings; Saving Your Preferred Settings - Gastroback DESIGN TOASTER DIGITAL 2S Bedienungsanleitung

Repeatedly press the "BREAD TYPE" button for moving the arrow in the program
menu ("<" or ">") to the desired program (see: 'Properties of Your New Toaster
/ 7 Preset Programs'). If you wish to change the browning, press the browning
buttons „–" oder „+" until the desired browning is shown on the display. Press
down the start lever until it engages in the lower operating position. The appli-
ance starts heating immediately. The "CANCEL" button illuminates red, while
the appliance is operating and the still remaining browning time is shown on
the display in a count down.
NOTE
You may change any settings even during operation. The appliance runs on using
your new settings immediately
CAUTION
– Do not attempt to terminate the heating process by moving
the start lever upwards to avoid damage the mechanic of the appliance. Press the
"CANCEL" button for terminating the heating process. However, you should wait
until the heating time elapsed and the count down reaches "00:00". If required,
select another program ("BREAD TYPE" button) or browning (see steps 3 and 4).
CAUTION
– After operation,only touch the bun tray at the dark handles. Do
not place the bun tray on heat-sensitive surfaces (e.g. sensitive tablecloth, coated
furniture), while the bun tray is hot
2. Let the appliance operate until the heating time ran out. For terminating the hea-
ting process prematurely, press the "CANCEL" button. The start lever springs
back to the idle position automatically, switching off the heating elements and
activating the standby mode.
CAUTION
– After toasting, your bakery produce will be hot!
3. After toasting in the bread slits: Take your bread slices out of the bread slits. If
required, you can move the start lever upwards a little for making it easier. After
heating on the bun tray: Holding the bun tray by the handles and ensuring to
keep it level, carefully remove the bun tray with the toasted bakery produce on
it. Place the bun tray on a heat-resistant surface (e.g. pot mat or china tablet).
4. Make a break of approx. 1 minute, before operating the appliance againand
toasting the next portion. This ensures a long life time of the heating elements.
If you do not wish to operate the appliance again, ensure that the appliance
is switched off (start lever is in the upper idle position, the "CANCEL" button
is dark). Then unplug the appliance. After each usage: Pull the crumb tray out
and empty it. Clean the appliance and the bun tray regularly (see: 'Care and
Cleaning').
EN
52

USING THE MEMORY FUNCTION

You can save your preferred settings in storage places of the appliance (see: 'Pro-
perties of Your New Toaster / Memory Function'). Thereafter, you can unplug the
appliance without loosing your individual settings.
IMPORTANT - For programming your own settings, you need to switch to program
mode first (see below: 'Saving Your Preferred Settings'). When selecting the memo-
ry function via the "MEMORY" button only (the numbers of the storage places are
displayed continuously), the appliance switches back to manual operation, whene-
ver you press another button (see above: 'Manual Operation').
NOTE
The settings for the "DEFROST" and "REHEAT" functions will not be saved (see: 'Pro-
perties of Your New Toaster / Toasting Frozen Bakery Produce'). You can activate
or de-activate these function any time you like after starting the heating process.

Factory Settings

On delivery, the program "WHITE" (plain wheat bread) and browning 4 are
selected for all storage places. You may recall the factory settings, whenever you
like. For this, hold the buttons "DEFROST" and "REHEAT" pressed, while connecting
the appliance to the power supply.

Saving Your Preferred Settings

IMPORTANT - When a new setting is programmed, the former setting will be over-
written without warning. The appliance uses your last settings always.
1. Prepare the appliance for operation (see: 'Preparing the Appliance for Operation').
2. Selecting the desired storage place: Shortly press the "MEMORY" button. The
numbers of the storage places (1-4) are shown on the display. The number of the
currently selected storage place is highlighted via a box. Press the "MEMORY" but-
ton repeatedly for selecting the desired storage place. With each storage place, the
assigned settings are shown on the display: program (bread type) and browning.
3. Switching to the program mode: Hold the "MEMORY" button pressed until the
numbers of the storage places start flashing (approx. 3 seconds).
EN
53