Changing The Activated Charcoal Filter (Only In Circulating-Air Mode) - Blaupunkt 5DL69650 Gebrauchsanleitung

Follow all instructions and warnings included with the cleaning
agents.
Area Cleaning agents
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth.
Clean stainless steel surfaces in the
direction of the grain only.
Special stainless steel cleaning prod-
ucts are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Painted surfaces Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth/towel.
Do not use any stainless steel clean-
ers.
Aluminium and Glass cleaner:
plastic Clean with a soft cloth.
Glass Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Operating controls Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth.
Risk of damage to the electronics
from penetrating moisture. Never
clean operator controls with a wet
cloth.
Do not use any stainless steel clean-
ers.
Cleaning the metal mesh grease filters
:
Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
Do not use any aggressive, acidic or alkaline cleaning
■
agents.
When cleaning the metal mesh grease filters, also clean the
■
holder for the metal mesh grease filters in the appliance
using a damp cloth.
The metal mesh grease filters can be cleaned in the
■
dishwasher or by hand.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
Do not clean heavily soiled metal mesh grease filters together
■
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
■
The metal mesh grease filters must not be wedged in.
By hand:
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
■
Removing metal grease filter
Fold the filter cover upwards.
1.
Notes
The opening angle of the filter cover is restricted to approx.
■
80°. Do not open the filter cover any further, otherwise the
hinges may be damaged.
The filter cover locks in any position.
■
Remove the two metal grease filters under the filter cover and
2.
the metal grease filter on the underside of the appliance.
Unfasten the lock, fold the metal filter forwards and remove it
from the bracket.
Note: Grease can accumulate at the bottom of the metal
grease filter. Hold the metal grease filter level, otherwise
grease will drip out.
Clean the metal grease filter.
3.
After removing the filters, clean the inside of the appliance.
4.
Clean the filter cover.
5.
Installing the metal mesh grease filter
Insert the two metal grease filters under the filter cover with
1.
the lock facing downwards.
Insert the metal grease filters on the underside of the
appliance.
Fold the metal grease filters inwards, locking them in place.
2.
Close the filter cover.
3.
Changing the activated charcoal filter (only in
circulating-air mode)
In order to guarantee efficient odour filtration, the filter must be
serviced regularly.
The activated charcoal filters must be replaced at least every
4 months.
Notes
The activated charcoal filters are not included in the delivery.
■
The activated charcoal filters can be obtained from specialist
retailers, from our after-sales service or from the Online Shop.
The activated charcoal filters cannot be cleaned or
■
reactivated.
Remove metal grease filter: See above.
1.
Turn the old activated charcoal filter and pull away from the
2.
bracket.
¨
Push the new activated charcoal filter onto the bracket and
3.
turn.
©
Fit the metal grease filter: See above.
4.
13