JVC KV-C1000 Bedienungsanleitung Seite 14

ELECTRICAL CONNECTIONS
When used with KD-AV7008:
Hideaway unit (supplied for KD-AV7008)
AV bus cable
(supplied) *2
The following is not required when connecting this TV tuner unit to KD-AV7008.
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle
does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealer.
Typical Connections
Before connecting:
• Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to the unit.
2
Finally connect the wiring
harness to the unit.
Black
1
To metallic body or chassis of the car
Yellow *1
2
3A
Red
3
To an accessory terminal in the fuse block
Blue with white stripe
4
To the remote control lead of JVC FM modulator KS-IF200
(for details, refer to the Instructions of KS-IF200.)
OPERATIONS
The following operations cannot be used when connecting this TV tuner
unit to KD-AV7008.
• When connecting to KD-AV7008, refer to the Instructions supplied with them.
• Before watching the TV, perform the area setup (see below).
1 Standby/On button
Press to turns on and off the TV tuner unit.
2 TV CH (channel) 5 / ∞ button
• Press to search for the TV channels ("SEARCH" appears). When a TV station is received, search will stop.
• Press and hold to activate manual search ("MANUAL" appears) for the TV station. Then press
repeatedly to change the TV channels.
3 AUTO PRESET button
• Press to display the preset channel list.
• Press and hold to preset the receivable TV stations automatically into the preset number buttons (1 – 12).
4 DISP (display) button
• Press to display the preset channel number on the monitor.
• Press and hold to call up the area setup screen. Then press number button (1, 2, 3, or 4) to select
your area. (Normally press 1. For New Zealand, press 2; for Indonesia, press 3; for CCIR, press 4.)
5 Preset number buttons (1 – 12)
• Press to select the preset channel number directly.
• Press and hold to store a TV station into preset number (1 – 12).
SPECIFICATIONS
TV TUNER UNIT
TV antenna jack × 4
AV bus terminal × 1
Remote sensor jack × 1
Output Video: RCA pin × 1; 1 V(p-p), 75 Ω
Audio: RCA pin × 2; 150 mV(rms)
Dimensions (W × H × D): 163 mm × 28 mm × 122 mm
Mass: 0.6 kg
All manuals and user guides at all-guides.com
Antenna element
Antenna base
Cord protector *1
*3
*1 Use this to protect the cord (not to be pinched with the door, etc.)
*2 For controlling KV-C1008 through KD-AV7008, this connection is only required. For other connections, refer to the manual
supplied for KD-AV7008.
*3 Reset the unit after installation is finished by pressing in with a ball-point pen or a similar tool.
1
Connect the colored leads of the power cord in
the order specified in the illustration below.
*1 Before checking the
operation of this unit prior
to installation, this lead
must be connected,
otherwise power cannot be
turned on.
*2
*2 Not included with this unit.
*2
To a live terminal in the
fuse block connecting to
the car battery (bypassing
the ignition switch)
Fuse block
DIVERSITY ANTENNA
Output impedance: 75 Ω × 4 (with mini plug)
Cord length: 5 m
Dimensions (approx.) (W × H × D):
440 mm × 490 mm × 18 mm (without the cable)
Mass (each unit) (approx.): 220 g (including the cable)
When used with another monitor system:
Monitor system
(separately purchased)
See "Typical
Connections"
below.
• Replace the fuse with one of the specified ratings. If the fuse blows frequently,
consult your JVC car audio dealer.
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
Connecting the remote sensor unit
• When used with any other monitor system than KD-AV7008.
• Before installing, make sure the remote controller functions properly with the remote
sensor unit placed in your selected position.
• Wipe clean the selected area sufficiently, and affix the remote sensor unit to the place firmly
after removing the protective sheet from the double-faced adhesive tape.
• Avoid any area on the dashboard, etc. subjected to direct sunlight.
Select an area where the remote sensor unit can receive remote signals through its
front face (sensing area).
Ignition switch
1
2
CAUTION
DO NOT leave the remote controller in a place (such as dashboards) exposed to
direct sunlight for a long time. Otherwise, it may be damaged.
NA
2
*3
Sensing area
Dashboard, etc
Double-faced adhesive
tape (supplied)
3
1 2
4
5
3
GENERAL
Channel coverage:
Australia VHF: ch 0 – 12
New Zealand VHF: ch 1 – 11
Indonesia VHF: ch 1A – 11
CCIR VHF: ch 2 – 12
Power requirement
Operating voltage: DC 14.4 V (11 V to 16 V allowance)
Grounding system: Negative ground
Allowable operating temperature: 0°C to +40°C
Design and specifications subject to change without notice.
Remote sensor unit
CR2025
UHF: ch 28 – 69
UHF: ch 21 – 69
UHF: ch 21 – 69
UHF: ch 21 – 69