Samsung SDP-850 Bedienungsanleitung Seite 2

SDP-850(DX) RS-232C Command Code
PC Transmit Data to MICOM
Command
2nd 3rd 4th
1st
AWC
0x01 0x00 0x05 0x00
AF 0x02
0x00 0x05 0x00
Lamp ON
0x00 0x05 0x00
0x03
Lamp OFF
0x00 0x0A 0x00
Internal
0x00 0x05 0x00
0x04
External 0x00 0x0A 0x00
Aperture ON 0x00 0x05 0x00
0x09
Aperture OFF 0x00 0x0A 0x00
Positive 0x00 0x05 0x00
0x05
Negative 0x00 0x0A 0x00
Power ON 0x00 0x05 0x00
0x0F
0x00 0x0A 0x00
Power OFF
0x00 0x05 0x00
FREQ 75Hz
0x0A
0x00 0x0A 0x00
FREQ 60Hz
PC Transmit Data to MICOM
Command
1st 2nd 3rd 4th
Freeze ON
0x00 0x05 0x00
0x12
Freeze OFF
0x00 0x0A 0x00
0x17
Preset Save
0x00 Number 0x00
0x18
Preset Exe 0x00 Number 0x00
Bright Up 0x00 0x05 0x00
0x21
Bright Down 0x00 0x0A 0x00
Red Up 0x00 0x05 0x00
0x23
Red Down 0x00 0x0A 0x00
Blue Up 0x00 0x05 0x00
0x24
Blue Down 0x00 0x0A 0x00
<Note1> Transmitting number "9" in image divide command, the system executes 3x3 multi-screen mode.
PC Receive Data from MICOM
Remark
1st 2nd 3rd 4th
0x01 "ACK data" 0x05 0x00
0x02
"ACK data" 0x05 0x00
"ACK data" 0x05 0x00
0x03
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x04
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x09
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x05
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x0F
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x0A
"ACK data" 0x0A 0x00
PC Receive Data from MICOM
Remark
1st 2nd 3rd 4th
"ACK data" 0x05 0x00
0x12
"ACK data" 0x0A 0x00
0x17 "ACK data" Number 0x00
Range: "1~4"
0x18 "ACK data" Number 0x00
"ACK data" 0x05 0x00
0x21
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x23
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x24
"ACK data" 0x0A 0x00
2
SDP-850(DX) RS-232C Command Code
PC Transmit Data to MICOM
Command
1st
2nd 3rd 4th
Focus Far
0x00 0x05 0x00
0x25
Focus Near
0x00 0x0A 0x00
Zoom Tele
0x00 0x05 0x00
0x26
Zoom Wide
0x00 0x0A 0x00
Bright Target 0x41
0x00 0x00 "data"
Red Target 0x43 0x00 0x00 "data"
Blue Target 0x00 0x00 "data"
0x44
Focus Target 0x00 "MSB data" "LSB data"
0x45
Zoom Target 0x00 "MSB data" "LSB data"
0x46
Focus/Zoom
0x05 "zoom MSB" "zoom LSB"
0x47
concurrent Target
0x0A "focus MSB" "focus LSB"
0x00 0x05 0x00
(2) Drive Stop 0x2F
<Note1> Depending of the zoom amount, the range of focus data will be changed. You can figure it out to see the table below. ("Focus-Status[Max]", "Focus-Status[Min]")
<Note2> Above 10 Command (Bright up/down, Red up/down, Blue up/down, Focus far/near, Zoom tele/wide) will go to all the way once you execute it.
"Drive Stop" can stop those command in certain point that you want.
PC Transmit Data to MICOM
Command
1st 2nd 3rd 4th
Set-Status(Normal)
0x61 0x00 0x00 0x00
Set-Status (Digital)
0x62 0x00 0x00 0x00
Message-Status
0x64 0x00 0x00 0x00
Bright-Status 0x65 0x00 0x00 0x00
Red-Status 0x67 0x00 0x00 0x00
Blue-Status 0x68 0x00 0x00 0x00
0x69
Zoom-Status 0x00 0x00 0x00
0x6A
Focus-Status 0x00 0x00 0x00
(1)
Focus-Status[Max] 0x00 0x05 0x00
0x6B
(1) Focus-Status[Min] 0x00 0x0A 0x00
<Note1> This command returns focus maximum/minimum data at current zoom position.
PC Receive Data from MICOM
Remark
1st 2nd 3rd 4th
"ACK data" 0x05 0x00
0x25
"ACK data" 0x0A 0x00
"ACK data" 0x05 0x00
0x26
"ACK data" 0x0A 0x00
0x41 "ACK data" 0x00 "data" Range: "1~120"
0x43 "ACK data" 0x00 "data"
Range: "1~200"
0x44 "ACK data" 0x00 "data"
Range: "1~200"
(1)
0x45 "ACK data" "MSB data" "LSB data"
Range: "0~2225"
0x46 "ACK data" "MSB data" "LSB data" Range: "0~1904"
"ACK data" "zoom LSB" "zoom LSB"
(1)
Focus: "0~2225"
0x47
Zoom: "0~1904"
"ACK data" "focus MSB" "focus LSB"
0x2D "ACK data" 0x05 0x00
PC Receive Data from MICOM
Remark
1st 2nd 3rd 4th
0x61 "ACK data" Status(MSB) Status(LSB)
Bit definition of
Status represents
0x62 "ACK data" Status(MSB) Status(LSB)
Page 4, 5
0x64 "ACK data" Status(MSB) Status(LSB)
0x65 "ACK data" 0x00 Status
Range: "1~120"
0x67 "ACK data" 0x00 Status
Range: "1~200"
0x68 "ACK data" 0x00 Status
Range: "1~200"
0x69 "ACK data" Status(MSB) Status(LSB)
Range: "0~1904"
0x6A
"ACK data" Status(MSB) Status(LSB)
Range: "0~2225"
"ACK data" Status(MSB) Status(LSB)
Range: "648~2225"
0x6B
"ACK data" Status(MSB) Status(LSB)
Range: "0~1383"
3