Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
User Manual
Package Contents
• Bluetooth
Speaker Conga
®
• Micro-USB charging cable
• User Manual
Overview:
1. Previous title / Vol- key
2. Music start-stop
3. Next title / Vol+ key
4. Multifunction button
5. Phone button
6. Speaker with LED
7. USB connection
8. Micro USB charging port
9. Status LED
10. 3.5 mm Audio Line-In
11. On/Off switch
12. Microphone
13. TF card slot
14. Bass reflex
Getting started
Charging the battery
Conga is equipped with an internal rechargeable lithium-Ion battery.
Connect the Micro USB cable with the micro USB charging port (8) of the
Conga. The cable can be connected to a computer or a standard USB
power adapter. The red LED (9) of Conga lights up while charging.
The normal charging time is 2-3 hours. The red LED turns off when fully
charged. The cable can be disconnected.
Note: Charge Conga for at least 2.5 hours before initial use.
Switching On /Off
Switch on: When powered off, switch the button (11) to the „ON" position.
Switch off: Switch the button (11) to the "OFF" position.
Note: Conga has a voice announcement, this can be given in German
or English.
Setting the language: Press the Music start-stop button (2) for 2 seconds
to change the language.
TWS Function
With the TWS function you can connect two conga speakers together to
achieve full stereo sound with 20 watts. To connect 2 devices together,
switch on both devices. Double press the Multifunction button (4),
the signal „TWS Function ready" will sound. After a few seconds the
speakers will connect to each other.
1
1 2 3 4
5
6
7
8
9
10
11
12
13
14
Attention: The Bluetooth
function of your smartphone must be switched
®
off during the setup of the TWS connection. Activate the Bluetooth
after both speakers are connected via TWS. To pair the speakers and the
smartphone, follow the steps described in the „Pairing" section.
Pairing
Conga must be paired with a Bluetooth
This is a two part process; one part is carried out on the Speaker and the
other is carried out on the other Bluetooth
Note: Please note that different mobile phones may require different
pairing methods.
1. Make sure that Conga is powered off. Set the power switch (11) to the
„ON" position. The pairing mode will start.
2. Use your mobile phone, computer or another Bluetooth
in order to search for Bluetooth
3. The Bluetooth
device should indicate that it has found „Conga".
®
4. Confirm pairing with Conga. Enter „0000" if you are asked for a
pairing code.
Note: If the connection is lost or the transmitter is temporarily disconnected,
press the music start/stop button (2) to reconnect.
Music playback
Music playback via Bluetooth
®
Start music playback on the Bluetooth
ga. The music is transferred to the Conga. Stop the music playback on the
Bluetooth
source to interrupt the streaming.
®
Note: The device must support A2DP and AVRCP profile to play and control
music over conga.
Music control
To play or stop music playback, briefly press the Start/Stop button (2).
To skip to the previous track, press the volume - button (1).
To skip to the next track, press the volume + button (3).
Playback via Line in / USB / TF card
Connect the medium from which the music is to be played to the Conga
speaker. The loudspeaker signals the music output and switches
automatically. The music is now played from the recognized medium over
the Conga.
Note: The buttons have no function when using the 3.5 mm Audio Line-In
connection. Use the audio source to control the music.
FM Radio
Press the multifunction button (4) once while the device is switched on to
switch to radio mode. If you now short press the Start/Stop button (2) for
about 2 seconds, the speaker will scan the bandwidth for receivable stations
®
device before use.
®
device.
®
transmitter
®
audio devices.
®
source which is paired with the Con-
®
GB
function
2
Werbung
Inhaltsverzeichnis
