ZAMST THUMB GUARD Gebrauchsanleitung Seite 2

How to mold and apply
• The thumb guard is a product that needs to be molded to fit your hand and fingers using hot water before use.
• Before molding and attaching this product, carefully read the "Precautions for use - Be sure to read this" section. Then follow the steps provided
to ensure the product is correctly molded.
• The molding and attachment steps below use the thumb of your right hand for reference. Follow the same steps for the left hand.
• The guard contains a resin that softens at a temperature of approximately 70 °C (158 °F), and hardens when cooled.
• If the product loses its original shape during use, its shape can be corrected by re-molding it. The product can be re-molded approximately 20 times.
1.
Prepare a container (such as a basin) that is large enough
to put the product in and a towel for drying.
2.
Fill the container with approximately 70 °C (158 °F) hot water.
3.
Unfasten all the hook-and-loop fasteners of the product.
Confirm the top/bottom and inside/outside of the product.
<Outside of the product>
Tag
<Inside of the product>
4.
Hold the support strap and the thumb strap with each hand
and immerse the product in hot water for 15 to 20 seconds.
Support
strap
5.
Remove the product from the hot water and dry it off
using a towel.
6.
Confirm that the product has cooled down so that you
can touch it. Fold the product in half from the center.
Disclaimer:
* The product specifications and appearance are subject to change without notice for the purpose of improvement.
* When disposing of this product, be sure to follow all disposal ordinances and regulations as specified by the local government.
* We take all possible measures to ensure product quality, however, if you find any defects, etc. in our products, please contact Nippon Sigmax Co., Ltd.
"ZAMST" and "ZAMST logo" are trademarks or registered trademarks of Nippon Sigmax Co., Ltd in Japan, the United States and other countries.
Be sure to use a heat-resistant
container.
70℃
(158 ℉)
Place the side with
the size tag on the
back of the product
facing down when
attaching the product
to your hand.
Thumb
strap
Be careful not to
burn yourself by
accidentally dipping
your hand in the hot
water.
Wrap the product
in a towel to dry it
thoroughly.
Be careful not to burn yourself.
* It takes about 60 to 90
seconds for the product
to reach an optimal
temperature after removing it
from hot water.
7.
Slip the finger loop over your thumb and position the
product where you want to place it.
Thumb loop
When attaching the product that has already been molded,
please start the steps from here.
8.
Fasten the support strap.
Temporary hook-and-
loop fastener
Hook-and-loop
fastener A
9.
Fasten the thumb strap.
Hook-and-loop
Thumb strap
fastener B
* Perform the following only when molding the product.
Press the entire guard with your other hand to fit it to the shape of
your hand and fingers, and wait until the guard hardens.
* After removing the guard from the hot
water, it hardens in 3 to 4 minutes.
* If you want the guard to harden
quickly, put it in cold water.
* If the guard hardens and it becomes
difficult to shape it, soak it in hot water
again, then shape it.
10.
Make sure that the product is not loose or out of place.
If you feel any discomfort, repeat the steps from the
beginning to reattach the product.
The product correctly fastened (right hand)
<Palm of hand>
11.
After the product has been molded, dry it in the shade.
Fasten the support
strap to the temporary
hook-and-loop fastener
while pulling the strap
lightly, and fasten hook-
and-loop fastener A to
the product.
Support strap
Fasten hook-and-loop
fastener B while lightly
pulling the thumb strap.
To make it easier to put
on a glove, etc. over the
product, pull the strap
downward and fasten.
<Side view> <Back of hand>