Operation - Aro SRGG31403A Gebrauchsanweisung

WARNING!
Use the appliance only after it has been completely assembled and adjusted!
Choosing gas
1. Propane gas cylinders can be used throughout the entire year. Butane gas cylinders work best during the summer. They are distinctly less effi cient at
temperatures under +10 °C.
2. We recommend using either 5 kg or 11 kg gas cylinders, for best performance.
3. Do not allow the cylinder to be fi lled beyond 80% capacity. Over-fi lled cylinders can create a dangerous condition due to build-up pressure and cause the
valve to expel propane gas vapours. The vapour is combustible and if it comes in contact with a spark source or fl ame an explosion causing severe burns,
bodily harm, or death could occur.
4. Always use a protective cylinder cap when appliance is not connected to the cylinder(s).
Gas connections
GB
WARNING! Be aware of fl ashback!
Make sure there is no debris, spiders, small insects or webs inside the head of the gas cylinder(s), pressure regulator(s), burner(s), burner tube(s)
or hose(s), before any connection is made. They can obstruct the gas fl ow, which could result in a fi re in and around the burner tube. This kind of
fi re is known as "fl ash-back" and can cause serious damages. Check and clean (→ CLEANING, MAINTENANCE AND REPAIR) all the parts of the
appliance before assembling it, to reduce the chance of its occurrence.
Connecting / exchanging gas cylinders
WARNING!
Only use the provided or equivalent pressure regulator(s) (→ TECHNICAL DATA) in order to guarantee that it functions safely and effi ciently. Using
an improper or a defective pressure regulator is dangerous. Consult your specialised dealer concerning suitable pressure regulators. The type of
the pressure regulator to be used must indicate that it complies with the relevant standard and requirement (EN 16129).
Consult your local gas retailer regarding suitable gas cylinders and pressure regulators (→ TECHNICAL DATA).
NOTE: Gas connections are equipped with left handed threads; the screw-nut needs to be turned counter clockwise!
1. Ensure that there are no ignition sources like cigarettes, open fl ames, sparks and other heat sources nearby when connecting or replacing gas cylinders.
2. Place the gas cylinder(s) on level ground next to the appliance.
3. Make sure that all control knobs on the appliance are in the off positions
4. Make sure that the gas valve of the gas cylinder(s) and / or the gas regulator(s) is / are closed.
5. Connect the gas hose(s) to the gas line(s) of the appliance (Fig. 1). Do not overtighten the connections. Use only the delivered hardware to secure the
connections. Do not use sealing tape or a liquid sealant.
6. Connect the / each pressure regulator to the gas cylinder inlet(s) by turning the pressure regulator counter clockwise (Fig. 2). Secure the connection(s) with
the retention nut(s).
7. Connect the other end of the gas hose(s) to the pressure regulator(s) (Fig. 3).
8. Check all connections for gas leaks (→ Testing for gas leaks).
1
Testing for gas leaks
WARNING! Risk of explosion!
Never check for gas leaks using a match or any other open fl ame.
Test all connections, fi ttings and all gas hoses for gas leaks every time prior use of the appliance, or each time the gas cylinder(s) is / are changed. Make sure
this procedure is carried out in a well ventilated area away from fl ames, sparks or any heat sources. Do not attempt to light the appliance, if you smell gas.
1. Make sure that all control knobs on the appliance are in the off positions
2. Open the gas valve of the gas cylinder(s) and / or the pressure regulator(s).
3. Apply leak detector spray or half water / half soap solution with a brush to all the connection points.
4. Turn the gas supply on the valve of the gas cylinder(s) and or the pressure regulator(s) off immediately, if you spot gas bubbles forming on the tested areas.
Tighten all connections again and repeat the test.
5. Do not use the appliance but contact your retailer, if gas bubbles keep forming.
Burning-off
Before fi rst use, remove any production residue and clean the appliance:
1. Operate the appliance at high temperature with the cover opened for about 10 - 15 minutes to burn-off production residues
(→ IGNITING THE BURNER(S)).
2. Turn the appliance off; allow it to cool and clean all parts (→ CLEANING AND CARE) afterwards.

OPERATION

WARNING! Danger of burns!
This appliance generates heat and escaping steam during use! Take proper precautions to prevent risk of burns, fi res, or other damages to people
and property! Wear protective oven mittens or gloves. Use proper tools like barbecue tong and prongs to turn over grillables!
(IM)3A-001327-0002_SRGG31403A_Multi_V2_200904.indb 14 (IM)3A-001327-0002_SRGG31403A_Multi_V2_200904.indb 14
2
2.
1.
1.
.
3
2.
2.
1.
.
14
07/09/2020 19:17 07/09/2020 19:17