j.e. StorkAir MX 10/10 Bedienungsanleitung Seite 45

Carry out Check to be carried out, if yes then go to next line:
check of:
VG 31 or
230V~ on the 'L'and thet 'N' clamp?
DNG 31
VG 31 or
10V = on the '+10V' and the 'GND'?
DNG 31
10V = on the clamps 'EN UIT' and the 'GND' swicht on
DNG 31
0V = on the clamps 'EN UIT' and the 'GND' swicht on
Adjust potentio-meter R1. Does the voltage vary between clamp '1' and the 'GND'?
DNG 31
(Reset the potentio-meter to the same voltage).
Adjust potentio-meter R2. Does the voltage vary between clamp '2' and the 'GND'?
DNG 31
(Reset the potentio-meter to the same voltage).
DNG 31 Switch the timer manually. Does the voltage vary between the 'E
DNG 31 Switch the timer manually. Does the voltage vary between the 'E
Remove the wire on the 'E
MX
soll
Connect up '10V' and the 'E
MX
Does the MX start working in high speed?
MX Remove the wire on the 'EN' clamp. Does the impeller stop?
MX Return the wiring to it's original state.
SAG Is there 10V = on the '10V'* and the 'GND' clamp?
SAG
Set the SAG to the '0' position. Does the MX switch off?
SAG Connect up the '10V'* and the 'EN' clamp. Does the MX start working in low speed?
Also connect up the '10V'* and the 'E
SAG
Disconnect the 'E ' wire. Does the MX start working in high speed?
soll
SAG Return the wiring to it's original state.
SAG Turn the regulator knob. Does the voltage vary on the 'E
Knob in position '0', no connection between the '10V'* and the 'EN' clamp. Knob in any other position,
SAG
with connection between '10V' and the 'EN' clamp. Is that correct?
VG 31 Turn the SAG knob. Does the voltage vary between the 'E
10V = on the 'EN UIT' and the 'GND' clamp. The SAG is not at position '0'.
VG 31
0V = on the 'EN UIT' and the 'GND' clamp. The SAG is at position '0'.
MX Remove the wire on the 'E
soll
Connect up the '10V' and the 'E
MX
Does the MX start working in high speed?
MX Remove the wire on the 'EN' clamp. Does the impeller stop?
MX Return the wiring to it's original state. Do the controls work well?
*Lorsqu'un LTG est utilisé, il faut lire pour la ''borne 10V'', ''borne 18V''
IN' and the 'GND'?
soll
UIT' and the 'GND'?
soll
' clamp. does the MX start working in low speed?
' clamp. Disconnect the 'E ' wire.
soll soll
' clamp.
soll
' and the 'GND' clamp?
soll
' UIT' clamp and the 'GND'?
soll
' clamp. Does the MX start working in low speed?
' clamp. disconnect the 'E ' wire.
soll soll
If no, then the malfuntion is in the:
electrical installation
VG 31 or DNG 31, Check the F3 fuse.
DNG 31
DNG 31
DNG 31
DNG 31 timer. See also the timer manual
for the timer control.
DNG 31 check the F2 fuse
MX controls
MX controls
MX controls
MX – SAG cabling
MX – SAG cabling
Is there release applied?
MX – SAG cabling
MX – SAG cabling
SAG
SAG
VG 31 check the F2 fuse
VG 31
MX controls
MX controls
MX controls
MX – VG 31 or the DNG 31 wiring
44
SAG or
SAG 0-2,
LTG +
SAG 0-5,
VG31
SAG 0-M, LTG
x
x
x
x x
x x
x x
x x
- x x
x x
x x
x
x
x
x
x
x
DNG 31
x
x
x
x
x
x
x
x
x
x
x
x
x
x