Anschlussdiagramm - Logico2 O2-Sicherheitssystem Bedienungsanleitung

5.

Anschlussdiagramm

Das Anschlussdiagramm zeigt ein Beispiel für eine mögliche Installation des Systems.
O2-Sensor Mk9
CO2-Sensor Mk9
CO2-Sensor Mk90
Möglichkeit der Erweiterung
mit bis zu acht Mk9-O2-
Sensoren oder Mk9/Mk90-
CO2-Sensoren
Bitte beachten Sie:
Jeder zusätzliche O2-Sensorsatz enthält eine separate Installationsanleitung, die beschreibt, wie
sich auf einfache Art zusätzliche Sensoren zu einem vorhandenen Set hinzufügen lassen.
CAUTION!
Altitude set to:
!
CO ALERT
Done by:
2
CO Sensor: Do not cover or place anything
2
in front of or on top of the sensor.
Indication Explanation
Green LED Unit in operation.
Red LED CO2 Awareness indication. The CO2 level is over 5000 ppm. No danger - but the CO2 is
unnaturally high. The display on the CO2 sensor will show "High".
- 5 sec -
Red LED Low-Alarm (High ambient CO2 concentration level) or TWA Alarm (5000 ppm/8 h Time
Weighted Average). The display on the CO2 sensor will show "Alarm" or "TWA High Alarm".
Connected remote warning strobe will be activated. Call Service.
Red LED High-Alarm (Dangerously high ambient CO2 concentration level). The display on the CO2
sensor will show "High-Alarm". The sensor will start flashing and connected remote warning
horn and strobe will be activated. Call Fire Departement.
Yellow LED CO2 sensor fault. The display on the CO2 sensor will show "Error".
Call Service.
CAUTION!
Altitude set to:
!
CO ALERT Done by:
2
CO Sensor: Do not cover or place anything
2
in front of or on top of the sensor.
Indication Explanation
Green LED Unit in operation.
Red LED CO2 Awareness indication. The CO2 level is over 5000 ppm. No danger - but the CO2 is
unnaturally high. The display on the CO2 sensor will show "High".
- 5 sec -
Red LED Low-Alarm (High ambient CO2 concentration level) or TWA Alarm (5000 ppm/8 h Time
Weighted Average). The display on the CO2 sensor will show "Alarm" or "TWA High Alarm".
Connected remote warning strobe will be activated. Call Service.
Red LED High-Alarm (Dangerously high ambient CO2 concentration level). The display on the CO2
sensor will show "High-Alarm". The sensor will start flashing and connected remote warning
horn and strobe will be activated. Call Fire Departement.
Yellow LED CO2 sensor fault. The display on the CO2 sensor will show "Error".
Call Service.
Dezentrale Anschlussbox
Splitter RJ45 (rot)
1-1/1-2/1-4
Splitter RJ45 (blau)
1-1/1-2/1-4
Netzteil
10
Signalhorn/Stroboskop
WARNING
!
Enclosed Space
Risk for Asphyxiation
DO NOT ENTER THIS AREA WHEN SIREN
IS SOUNDING AND LIGHT IS FLASHING!
Risk for
Low Oxygen
Emergency Actions
Level • Evacuate the Area Immediately.
• Call the Fire Department from
outside of the building.
Blue Light
Power ON
WARNING
!
Enclosed Space
Risk for Asphyxiation
DO NOT ENTER THIS AREA WHEN SIREN
IS SOUNDING AND LIGHT IS FLASHING!
Risk for
Low Oxygen
Emergency Actions
Level • Evacuate the Area Immediately.
• Call the Fire Department from
outside of the building.
Blue Light
Power ON
Zentralgerät Mk9
O2 Safety System - Mk9
What to do in case of an ALARM?
1. Keep Calm!
2. Turn off the sounding alarm on the Central Unit by pressing the RESET button
3. Check the type of alarm and which Sensor is giving the alarm by following the instructions below.
INDICATION
Central Unit:
• The red diode is ON
• Constant sound signal
Display:
TAKE PRECAUTIONS
• Sensor number, O2 % and
Gateway Alarm A Low concentration of O2
Central Unit:
• The yellow diode is blinking
• Beeping sound signal
Display:
• Sensor number, (Fault
information)
After an alarm, always reset
the system.
Test the alarm to insure that
communication, warning lamps
and sounders function.
Sensor Place
1
2
3
4
!
!
on the front.
CAUSE ACTION
ALARM
DO NOT ENTER
the risk zone.
!
Evacuate the area if
O2 level is under 19.5%.
SYSTEM FAULT Check the manual, communication
cables and O2-Sensor.
If no fault is found, call service.
Phone: .....................................
ALARM RESET Press reset button until "Alarm
cleared" is shown in the display.
ALARM TEST Press reset button until "Testing
system..." is shown in the display.