Extended Menu - Seav LRX 2281 Bedienungsanleitung

that moment the automatic closing time will be stored and the T.
PAUSA LED will stay on steady. If you wish to restore the initial
condition ( without automatic closing ), move to the flashing T.
PAUSA LED, then press the SET key twice within 2 seconds;
the LED will shut off and the operation will be complete.
During programming the radio control key of the control unit can
be used instead of the SET key, if stored previously.
8) T. RIT. ANTE :
(Programming door delay of 15 sec. Max.)
The control unit is supplied by the manufacturer without gate
delay during opening and closing. If it is necessary to enter a
gate delay time, programming must be carried out when the
gate is closed, as follows: use the SEL key to move to the
flashing RIT. ANTE LED, press the SET key, wait for desired
interval of time, then press the SET key again: the gate delay
time opening will be stored, at 2 seconds, of the delay time of
the door closing for the time programmed and the RIT. ANTE
LED is steady.
To restore the initial configuration (without door delay), go to
the RIT. ANTE LED when flashing then press the SET key twice
within 2 seconds, the LED goes off and the operation is
completed.

EXTENDED MENU 1

The control unit is supplied by the manufacturer with the
possibility of selecting only the main menu functions.
To enable the functions listed in extended menu 1, proceed as
follows: press the SET button and hold for 5 seconds, after
which the T. PAUSA LED and RIT. ANTE LED will flash
alternately. You have 30 seconds to select the functions of
Extended Menu 1 using the SEL and SET buttons. After
another 30 seconds, the control unit returns to the main menu.
---------------------- EXTENDED MENU 1
Reference LED LED Off
A) AUT / P-P PGM remote = OFF
B) CODE Test Photocell = ON
C) CODE PED. Mant. Pressure = OFF
D) INB.CMD.AP Water Hammer = OFF
E) T. MOT. Closing Hammer = OFF
F) T.MOT.PED. Safety Device 2
G) T. PAUSA Alternate ON/OFF flashing light
H) RIT. ANTE Flashing beacon ON/OFF in alternation
A) AUT / P-P
( Remote programming of radio control ):
The control unit allows the transmission code to be
programmed, without using the SEL button directly on the
control unit, but remotely.
The remote transmission code can be programmed as follows:
continuously sending a previously-memorised radio control
code for more than 10 seconds. At this point the control unit
switches to programming mode, as described above for the
CODE LED in the main menu.
The control unit is supplied by the manufacturer with the remote
transmission code programming function disabled. If you wish
to enable the function, proceed as follows: check that Extended
Menu 1 is enabled (RIT. ANTE LED and T. PAUSA LED start
flashing alternately, with the SEL key positioned on the flashing
of AUT/ P-P LED then press the SET key, the AUT/P-P LED will
simultaneously stays on steadily and
completed. Repeat the procedure to restore the previous
configuration.
B) CODE ( Test Photocell ) :
The control unit is supplied by the manufacturer with photocell
Test programming enabled (in accordance with Standard EN
12453). If you wish to disable the function proceed as follows:
check that Extended Menu 1 is enabled (T. PAUSA and RIT.
ANTE LEDs flashing alternatively), with the SEL key position on
the flashing of CODE LED then press the SET key, the CODE
LED will simultaneously stay on steady and programming is
------------------
LED On
PGM remote = ON
Test Photocell= OFF
Mant. Pressure = ON
Water Hammer = ON
Closing Hammer = ON
Block Input
programming is
completed. Accordingly, the photocell test will not be carried
out, therefore even if not connected (if unused, DS1 and DS2
inputs must be jumped), the control unit is enabled for
operation. Repeat the procedure to restore the previous
configuration.
Important: In the LRX 2281/NT series control panels the
photocell test is deactivated by default, but can be activated by
following the procedure described above.
C) CODE PED ( Hydraulic Motors Maintenance Pressure ) :
The control unit is supplied by the manufacturer with the
hydraulic motors maintenance pressure function disabled. If you
wish to enable the function, proceed as follows: make sure that
you have enabled Extended Menu 1 (T. PAUSA LED and RIT.
ANTE LED start flashing alternately), with the SEL key position
on the flashing of CODE PED LED then press the SET key, the
PED CODE LED will simultaneously stay on steady and
programming is completed. Accordingly the control unit will
send a closing command every 2 hours to the motor for 2
seconds. Repeat the procedure to restore the previous
configuration.
D) CODE PED. ( Water Hammer ) :
The control unit is supplied by the manufacturer with Water
Hammer disabled. If you wish to enable the Water Hammer
function, proceed as follows: check that Extended Menu 1 is
enabled (RIT. ANTE LED and T. PAUSA LED start flashing
alternately), with the SEL key position on the flashing of
INB.CMD.AP LED then press the SET key, the INB.CMD.AP
LED will simultaneously
programming is completed. If you wish to enable the Water
Hammer function to the power set through the "POWER"
Trimmer, repeat the operation described above, pressing the
SEL button twice instead of once (making the INB.CMD.AP.
LED flash rapidly). Repeat the operation to restore the initial
configuration.
Accordingly, we can facilitate the release of the gate and
therefore allow the proper execution of the opening phase. In
fact, the control unit, before starting the opening phase sends a
closing command for 2 seconds with power relative to the
choice selected.
E) T. MOT. ( Closing Hammer ) :
The control unit is supplied by the manufacturer with the
Closing Hammer Function disabled. If you wish to enable the
Closing Hammer function, proceed as follows: make sure that
you have enabled Extended Menu 1 (RIT. ANTE LED and T.
PAUSA LED start flashing alternately), with the SEL key
position on the flashing of T.MOT. LED then press the SET key,
the T.MOT. LED will simultaneously switch on permanently and
programming is completed. If you wish to enable the Closing
Hammer function to the power set through the "POWER"
Trimmer, repeat the operation described above, pressing the
SEL button twice instead of once (making the T.MOT. LED flash
rapidly). Repeat the operation to restore the initial configuration.
Accordingly the control unit, if functioning with Deceleration
during closing, will reach (after having completed the
deceleration closing phase) a time of 1 second with power
relative to the choice selected in order to overcome the gate
installed.
F) T. MOT. LED ( Safety device 2 / Block ) :
The control unit is supplied by the manufacturer with the Block
input function disabled. If you wish to enable the function,
proceed as follows: make sure that you have enabled Extended
Menu 1 (T. PAUSA LED and RIT. ANTE LED start flashing
alternately), by using the SEL key select the flashing T. MOT.
PED. LED and press the SET button: T. MOT. PED. LED stays
steadily lit and programming is complete.
Accordingly the control unit, changes the function provided for
Safety Device 2 input ( CN2 no. 9-10 ) in safety block input with
the following function: the intervention in any function phase of
the control unit triggers the immediate stop of motion. A further
switch on permanently and