Kiano Elegance Robot Original Bedienungsanleitung Seite 11

FAQ
Failure
It cannot be turned on.
It cannot be charged.
The machine cannot be returned for
charging.
The device cannot be found in the mobile.
The machine is offline.
The mobile and the device cannot be
paired.
There is abnormal voice during cleaning.
Cleaning is not effective.
Timing cleaning doesn't work.
Whether it needs to be charged for 24
hours for the initial use.
Whether the power of the charging
s t a n d i s n e e d e d t o b e c u t o ff a f t e r
charging is completed.
Whether the laser emitted by the laser
radar is harmful to the human.
Safety information
Battery and charging
01. Do not use any battery, charging stand or charger from third-party.
02. Please make sure that the voltage used is correct.
03. Do not disassemble, repair or modify the battery or the charging stand.
04. Do not place the charging stand and the main machine close to the heat source, such as heating radiators, induction cookers,
ovens, etc.
05. Do not wipe anywhere of the product with a damp cloth or any liquid.
06. Do not discard used batteries at will and please give the professional recycling agency for treatment.
07. If the power cord is damaged or broken, please stop using it immediately, and contact us in time to select the proper channel
to purchase the genuine power cord for replacement.
08. Please make sure that the main machine is turned off for transport and it is recommended to pack with the original box.
09. If the product is not used for a long time, please turn off the power after fully charged, turn off the main machine, store in a
cool dry place, and charge it at least every 3 months to avoid damage to the battery.
Laser safety information
Lidar of the product complies with the IEC 60825-1:2014 (Third Edition)
Applied standard
GB4706.1-2005, GB4706.7-2014, GB4343.1-2009, GB17625.1-2012
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-
sired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
The battery is low, please charge it before use. The ambient temperature is over low or over high,
please use it in the range of 0°C-40°C.
The charging stand is not powered, please make sure the power is connected successfully. Poor
contact of the charging electrode, please clean the charging stand electrode and the machine electrode.
Make sure there is enough space around the charging stand. And make sure that the recognition area
on surface of the charging stand is free of dust and dirt.
Please reconnect WiFi and ensure that the network connection to the machine is successful.
Please ensure that the network connection of the machine is successful. And make sure the machine is
always within the WiFi signal coverage.
Make sure the machine and the charging stand are within the WiFi signal coverage and the signal is
good. Please try resetting WiFi before pairing.
Please check and clean the foreign matters on rolling brush, side brush, drive wheel and the universal
wheel, and clean the machine chassis and anti-collision strip.
Please check and clean the dust box and filter. Please replace the filter if it is blocked. Check and clean
the rolling brush if it is entangled.
Timed cleaning cannot be triggered if the battery is low. Please confirm that the machine is connected to
the network, otherwise, the timing cleaning task cannot be synchronized.
The built-in high-performance lithium-ion battery has no memory effect, and it can be used after being
fully charged and no need charging of 24 hours.
In daily use, the standby power consumption is very low, so no need to power off and shut down, and
maintaining the charging state is beneficial to the best performance of the battery. If it is not used for a
long time, please cut off the power of the charging stand and shut it down for storage. It is recommended
to charge once a month to avoid damage to the battery due to over-discharge.
The machine adopts advanced and safe laser radar, which meets the CLASS I laser standard and eye
safety level.
Trouble-shooting
EN
11