Quell COUNTERTOP FILTER Gebrauchsanweisung Seite 2

EN
Thank you for choosing Quell advanced filtration technology.
¬ A simple, modern design ensures that the Quell countertop water filter unit
will blend in with any kitchen. The unit sits securely on its non-slip base.
¬ The Quell countertop water filter unit is easily connected to the water supply
so you can enjoy pure, fresh and great tasting water from your tap any time.
¬ For correct installation, use and maintenance, please read these
instructions carefully and keep for future reference.
¬ If you need to replace the filter cartridges, use Quell filter cartridges.
Product technical specification
Flow rate 3 l/min
Max. pressure
690 kPa**
Filter capacity
3000 l
Water source municipial water
Filter life
6 months*
Package contents
(see page 20)
1 Two stage filtration unit
2 Filter cover
3 Carbon Block filter or
PP sediment filter
4 Disruptor™ PACV filter
5 Hose
6 Chrome plated tap spout
7 Chrome plated three-way
valve with gasket
8 Thread adapter with gasket
9 Round threaded nut
10 Outlet hose nipple
11 Filter unit inlet
12 Control valve
13 Locking clip
2
Caution
The water source should be
municipal water. If you use a water
source other than public water, it is
important that the water source is
appropriately controlled to ensure
that it is safe for domestic use!
Filter cartridge replacement
Remove filter cover. Turn filter
1
cartridge counter-clockwise. Pull
the filter upwards to remove.
Insert new filter cartridge into the
2
filter head. Turn filter clockwise
until it stops. Replace filter cover.
Perform the steps according
3
to points 3 and 4 of
Operating instructions.
Replacement filter cartridges
¬ Disruptor™ see page 16
¬ Carbon Block see page 17
¬ PP Sediment
see page 17
Sold separetly
INSTALLATION
Connecting system for use
Unscrew the end cap on
1
the end of your tap.
If the thread on the end of your tap
2
is on the inside, screw in the wider
diameter of the supplied thread adapter
(8) into tap end and tighten with
fingers. Otherwise proceed to step 3.
Screw on the three-way valve (7) either
3
onto the thread adapter or directly
onto tap end. Tighten with fingers.
Unscrew the round threaded nut
4
(9) off the outlet hose nipple on the
chrome plated three-way valve and
slide it onto one end of hose (5).
Push hose firmly onto outlet
5
hose nipple (10) until it is sitting
flush against thread.
Secure by tightening the
6
round threaded nut.
Remove blue locking clip (13) from
7
the filter unit inlet (11), pull out the
blue blind plug (at the same time
the white round reducer must be
pushed inwards) and connect other
end of hose into the filter inlet hole
until it stops. Apply the blue locking
clip into the inlet to secure hose.
Write the date of installation on the
8
sticker on the filter cartridges.
Tap set-up
Internal thread
set-up
Operating instructions
When the control valve (12) on the
1
chrome plated three-way valve
is in the down position, the water
from the tap will come directly
from the tap (unfiltered).
When the control valve is at horizontal
2
position (rotated 90 degrees),
the water will pass through the
two stage filtration unit. Check for
leaks and adjust if necessary.
Let the water run through the system
3
for 3 minutes to flush filter cartridges.
Allow the system to stand for 3 hours
4
(to activate the Disruptor filter) and then
flush again for 3 minutes. The filtration
system is now ready to use. Water flow
reduction usually indicates clogging of
filter cartridges. Filter cartridges should
be changed based on filter changing
instructions. The service life will vary
due to water quality and usage.
External thread
set-up
E N
3