Safety Precaution; Installation Instructions - Glem GHE601SI Betrieb Und Wartung Handbuch

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultane-
ously with an open fireplace or burner that depend on the air
in the environment and are supplied by other than electrical
energy, as the cooker hood removes the air from the environ-
ment which a burner or fireplace need for combustion. The
negative pressure in the environment must not exceed 4Pa
(4x10-5 bar). Provide adequate ventilation in the environment
for a safe operation of the cooker hood. Follow the local laws
applicable for external air evacuation.
Before connecting the model to the electricity network:
- Control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to the
network and the socket is suitable. If in doubt ask a qualified
electrician.
- If the power supply cable is damaged, it must be replaced with
another cable or a special assembly, which may be obtained
direct from the manufacturer or from the Technical Assistance
Centre.
- This device must be connected to the supply network through
either a plug fused 3A or hardwired to a 2 fase spur protected
by 3A fuse.
2. Warning!
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the filters while the cooker
hood is operating.
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker
hood.
D) Avoid free flame, as it is damaging for the filters and a
fire hazard.
E) Constantly check food frying to avoid that the over-
heated oil may become a fire hazard.
F) Disconnect the electrical plug prior to any maintenance.
G) This appliance is not intended for use by young children
or infirm persons without supervision.
H) Young children should be supervised to ensure they do
not play with the appliance.
I) There shall be adequate ventilation of the room when
the rangehood is used at the same time as appliances
burning gas or other fuels.
L) There is a risk of fire if cleaning is not carried out in
accordance with the instructions.

INSTALLATION INSTRUCTIONS

• Assembly and electrical connections must be carried out
by specialised personnel.
• Wear protective gloves before proceeding with the instal-
lation.
• Electric Connection:
- The appliance has been manufactured as a class II, therefore
no earth cable is necessary. The plug must be easily acces-
sible after the installation of the appliance. If the appliance
is equipped with power cord without plug, a suitably di-
mensioned omnipolar switch with 3 mm minimum opening
between contacts must be fitted between the appliance and
the electricity supply in compliance with the load and current
regulations.
- The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral.
• If the hob is electric, gas, or induction, the minimum distance
between the same and the lower part of the hood must be at
least 65 cm. If a connection tube composed of two parts is
used, the upper part must be placed outside the lower part. Do
not connect the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes from other
appliances generated by other than an electrical source.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which has the
same diameter as the air exhaust outlet hole. If a pipe with a
smaller diameter is used, the efficiency of the product may be
reduced and its operation may become noisier.
• Warning: if the bulbs are not working, ensure that they are
screwed in fully.
• Installation:
Prior to proceeding with the assembly operations (according
to the model that you have purchased), to facilitate handling
of the device, remove the grille as indicated in figure 6.
• Fitting the front panel:
To make fixing the front panel in place easier, the cooker hood
flap may be removed in the following manner:
1- Pull the flap out until it reaches its opening limit (Fig.7A).
2- Push the opening limit tabs F downwards (Fig.7B) and
completely remove the flap from the guide rails.
3- After fixing the front panel to the flap (Fig.7C), replace
everything by performing the above instructions in reverse.
4- When replacing the grille, be sure to insert the buffer S into
the casing, as demonstrated in figure 7D.
• This device may be installed in two different ways:
1. Fixing the hood to the lower part of the wall cabinet
(Fig.2):
- Make 4 holes in the wall cabinet respecting the measurements
indicated in figures 2A-2C.
- Position the hood underneath the wall cabinet and fix it into
place using 4 screws (supplied) suitable for the type of cabinet.
2. Fixing the hood to the wall (Fig.2):
- Make 4 holes in the wall cabinet respecting the measurements
indicated in figures 2A-2B.
- Hang the hood on the wall, using the 2 holes H, align it in a
horizontal position and fix it definitively to the wall using the
two safety holes I (Fig.2B).
For the various installations use screws and screw anchors
suited to the type of wall (e.g. reinforced concrete, plaster-
board, etc.).
If the screws and screw anchors are provided with the product,
check that they are suitable for the type of wall on which the
hood is to be fixed.
• The hood is already prepared for the version with which it
was ordered. The versions may be:
- E xtraction (Fig.1B-4).
- Filter (Fig.1A-5-8).
- If the hood is an extractor model, the lever C must be posi-
tioned as indicated in figure 4.
- If the hood is a filter model, the lever C must be positioned
as indicated in figure 5.
• Extractor version:
The appliance expels the fumes through an outside wall or
- 13 -