Maintenance And Care; Maintenance And Troubleshooting - kikkaride BOBBY Gebrauchsanweisung

2.3. Now remove the Foam Tube from the Metal Rod. Insert the rod of the Front Wheel Assembly through the bottom of the Wiggle Car and then re- t
the Foam Tube before pushing the Metal Rod up into the socket at the top of the car. Push the wheels in as far as you can by hand and then see the
special note below.
It is very important to ensure that the round metal bearing at the bottom of the metal rod (this is the bit that looks like a ring or collar at the bottom of
the rod) ts completely into the round socket in the underside of the car. You should not be able to see any of the sides of the bearing after it has been
pushed into the socket. You may need to use a mallet or hammer, to persuade the bearing into the socket. Hit the assembly from underneath between
the small front safety wheels and the larger drive wheels. If you do use a mallet or hammer to do this use a piece of wood or old magazine to cushion
the blows between the hammer and the plastic as you hit. When you have hit the bottom bearing in make sure that the bearing on the top of the
Wiggle Car has not been dislodged during the hitting. If the top bearing has been moved by the banging, then simply tap it back into the Wiggle Car
body until it is level with the body again.
Figure 3
If your Steering Wheel has the nut, washer and bolt already tted go to section 3.1. If the nut, washer and bolt are loose in the box then go to section
3.2.
3.1. If your Steering Wheel has the nut, washer and bolt already xed in it. Hold the steering wheel in one hand. With your other hand you need to turn
the bolt so that the raised tongue you will see on the side of the bolt at the bottom sits into one of the grooves cut into the metal shaft under the
Steering Wheel. (You may need to loosen the nut rst to let you do this.) Then, holding the bolt in place with one hand, use the Box Spanner to hand
tighten the nut in the center of the wheel.
3.2. If the nut, washer and bolt are loose when you receive your Wiggle Car. First have a look at the bolt. You should see that there is a raised piece on the
cone shaped end. Take the bolt and put it into the steering wheel from the bottom with the threaded end rst. Push the bolt as far into the center of the
see Picture 3.2,3.3). As you push the bolt in turn it so that the raised piece on the side of the bolt at the bottom sits into one of the grooves cut into the
metal shaft under the Steering Wheel. Then keep holding the bolt in place with one hand and with your other hand put the washer over the threaded
part of the bolt and then screw the nut onto the threaded end using the Box Spanner to hand tighten only enough to stop the xing bolt from turning.
3.3. Now put the Steering Wheel into the hole on the top of the Wiggle Car. The metal part under the Steering wheel now sits inside the metal Metal
Rod.
Figure 4.
4.1.You now need to line up the Steering Wheel and the Front Wheels. Position the Front Wheels so they point along the line of the Wiggle Car with the
small wheels pointing forward. Place the Steering wheel so that when sitting on the Wiggle Car the Steering Wheel should look like a butter y shape in
front of you.
4.2. Now, hold both the Steering Wheel and front wheels in place. Tighten the nut in the center of the Steering Wheel fully using the shaft of a
screwdriver or metal rod placed through the holes in the Box Spanner . You can also use a 17mm socket wrench to tighten the nut e ectively.
Tightening the nut will secure the connection between the Steering Wheel and the Metal Rod. Note: Make sure that when tightening the nut you hold
both the Steering Wheel and Front Wheels in place so as to prevent them moving and twisting out of line as you tighten. See special note
Special Note: Make sure to tighten the nut signi cantly. This is critical to the performance of your Wiggle Car.
4.3. When the Steering Wheel and the Front Wheel are secure after tightening the nut put the Red Plastic center cover into the center of the Steering
Wheel and you are ready to ride!!

MAINTENANCE AND CARE

Plastic and metal parts
1. The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
2. Do not let the product exposed to the harmful e ect of external factors - direct sunlight, rain, snow or wind. This may lead to damage of the metal
and plastic parts and fading of the fabrics of the crib.
3. When you are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low room
temperatures.
From time to time check all plastic parts that are hanged on the frame. Tighten all screw and bolts if necessary.
MAINTENANCE AND TROUBLE SHOOTING
After assembling your Wiggle Car, should the steering become loose or you nd the car doesn't move when the steering wheel is turned, it is likely that
the nut in the middle of the steering wheel is not tight enough.
If this happens, rst check that the bearing at the bottom of the steering column has been pushed completely into the socket under the Wiggle Car. If
you can see any of the side of the bearing, even just 1 or 2 mm, then you need to get the bearing further into the socket. To do this, rst remove the
steering wheel by taking o the red center cap and loosening the nut. Then tap the top of the bolt to loosen it and lift the steering wheel o the Wiggle
Car. Then repeat section 3 and 4, see especially the notes in section 3.
ENGLISH