Cable Installation; Maintenance - Milwaukee M18 FCSSM Original Bedienungsanleitung

CAUTION Extended operation of the tool in reverse can
cause damage to the cable and accessories.
If it is hard to get the cable through a trap or other fi tting,
the following methods or combination of methods can be
used.
1. Sharp downward thrusts on the cable, both with and
without the cable rotating, can help the cable through a
trap.
2. With the lever arm released, rotating the cable by hand
can change the orientation of the cutter to allow it to
more easily negotiate the fi tting.
3. Run the drain cleaner in REV rotation for several
seconds while pushing down on the cable. Only do this
long enough to get the cable started through the trap.
Running the cable in reverse can damage the cable.
If these options do not work, consider using a smaller
diameter or more fl exible cable.

CABLE INSTALLATION

Selecting the proper cable:
Cable Cable Style Pipe
Size Diameter
ø 16 mm Milwaukee Open Wind 32-90 mm
cable
ø 22 mm Milwaukee Open Wind 75-160 mm
cable
To prevent damage to the cable and attachments, only use
in recommended size
For cable installation see picture section.
WARNING! Cable is under pressure and can recoil
unexpectedly during installation, which may result in
personal injury.
To reduce the risk of injury, wear safety goggles or glasses
with side shields. Always wear leather gloves.
Read operator's manual. Use protective equipment.
Chemicals, bacteria and other substances that may cause
bums, be toxic or infectious may be present.
Use hot, soapy water to wash hands after handling.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool,
please reference the Quick Start guide included with this
product or go to www.milwaukeetool.com/one-key. To
download the ONE-KEY app, visit the App Store or Google
Play from your smart device.
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset
manually to recover.
We considered the results to be within our minimum
acceptable performance level according to
EN 55014-2:2015 / EN 301489-1 V2.1.1 / EN 301489-17
V3.1.1.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready to be
confi gured via the ONE-KEY™ app.
Blinking Blue Tool is actively communicating with the
ONE-KEY™ app.
Blinking Red Tool is in security lockout and can be
unlocked by the owner via the ONE-
KEY™ app.
26 ENGLISH
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions and the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-3-14:2017
EN 55014-1:2017
EN 55014-2:2015
EN 62479:2010
EN 300 328 V2.1.1
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
EN IEC 63000:2018
Winnenden, 2020-10-15
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

MAINTENANCE

Cleaning cables, tube and machine
The cable and tube should be thoroughly fl ushed with
water after every use to prevent damaging eff ects of
sediment and drain cleaning compounds.
WARNING! Always wear leather gloves over latex / rubber
gloves to avoid entanglement. After washing, dry the cable
and tube completely. Then, wipe cable with an oiled rag
before returning it to its carrier.
Cleanout procedure:
1. Insert the battery pack and close the battery door.
Switch the tool into forward position .
2. Press lever and run tool for 30 seconds. Insert cable and
check function.
3. Tip tool on an angle with the front of the tool pointing
upward.
4. Flush the tool continually with water until all components
appear to be moving freely.
5. Repeat steps 2-6 until all components are moving freely.
Continue to fl ush with water as necessary until the tool is
functioning normally.
NOTE: Avoid using high pressure water when cleaning the
tool. Only clean the tool using water. No additives such as
degreasers or drain cleaning
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the
six-digit No. on the label and order the drawing at your
local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Wear gloves!
Always wear goggles when using the machine.
Do not swallow the coin cell battery!
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
n
No-load speed
0
V
Volts
Direct current
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 27