Inventory; Loose Parts & Overview; General Setup - laguna FUSION3 Gebrauchsanweisung

Receiving your tablesaw
Pic. 11
This is how machine is shipped from the
factory.
Unscrew the crate fasteners
Pic. 12
Use a drill with a #2 Phillips head bit and
remove the bottom screws from carton. These
screws may be discarded.
Lift crate off pallet
Pic. 13
Use two persons to lift the carton away from the
pallet. There should be three packages along
with the table saw.
NOTE: The throat plate, riving knife, and 10"
blade is pre-installed in the machine. The miter
gauge, and blade changing tool are positioned
in the tool holder located on the right side of the
cabinet.
Check Inventory
Pic. 14
1. Fence, install tools, push stick, blade guard
assembly
2. Smaller fence rail sections, hardware kit
3. Longer fence rail sections.
Wipe off protective plastics
Pic. 15
www.igmtools.com
Peel back the protective vinyl plastic and wipe
away the oil with a waste rag.
Use Caution: An oily rag can be a serious fire
hazard. Discard in an appropriate manner.
Tech Tip: To help keep your table top clean and
to prevent or clean any rust, we recommend
waxing your tabletop with an appropriate wax
rubbing compound. This will also reduce friction
under operation. Rust can be removed with
WD-40.

6.2 Inventory

Box 1
Fence: PTSF236110175-0130-1-1
Push stick: PTSF236110175-0130-130
Blade guard: PTSF236110175-01302-1
Install Tools
Fence hooks*: PTSF236110175-0130-118
* Fence storage hooks may be pre-installed.
Box 2
Rear Rail 2: PTSF236110175-0130-127.5
Front Rail 2: PTSF236110175-0130-127.6
Hardware kit
Box 3
Rear rail 1: PTSF236110175-0130-127.5
Front rail 1: PTSF236110175-0130-127.6
Pre-installed on machine
Throat plate PTSF236110175-0130-6
Riving knife PTSF236110175-0130-27
250mm blade PTSF236110175-0130-33
Mitre gauge PTSF236110175-0130-3
Arbor wrench PTSF236110175-0130-137
Tool storage PTSF236110175-0130-120
Wings (2x) PTSF236110175-0130-4
Note: The front rail part number is comprised of
two pieces – both long and short. The rear rail
part number is comprised of two pieces – long
and short.
Note.: For safety reasons, this machine is not
sold with a tape-rule for the left side of the
blade. It is not a missing part.
6.3 Loose Parts & Overview
Your new machine has been mostly assembled
at the certified ISO 91001 factory where it was
made. Some parts must be assembled by the
purchaser. Please read all steps first before
proceeding with step one.
Pic. 16
-8-
Blade Guard
Pic. 17
5) M8x1.5+ lock washer + washer + nut
Pic. 18
(5) Square head 8x1.5 + washer + nut
Pic. 19
Fence hooks (step 2)
Pic. 20
Pic. 21

6.4 General Setup

1. Attach the short rear fence support
2. Attach the long rear fence support
3. Level the rear rails and fasten
4. Attach T-Slot bolts to front table
5. Insert long front rail fence support
6. Insert short front rail and switch
7. Join front fence supports
8. Align the entire front rail to blade mark
9. Level and fasten the front rail
10. Insert fence
11. Level the saw by adjusting casters
1. Attach short rear fence support
Use the supplied wrench and Alan key to
loosely fasten (2) bolts, lock washers, washers,