Replace The Gas Cylinder; Starting Up; Shutting Down; Storage / Care / Repair - EINHELL PS 13 Niro Betriebsanleitung

Anleitung PS 13 Niro_SPK7
GB
provided on the pressure regulator for this pur-
pose) in order to stop the regulator being turned
or too much force being transferred. Use the
above tool to tighten the screw connection and to
guarantee tightness and prevent leaks.
3. Check all the connections at operating pressure
for leaks using a leak tester. If there are no
bubbles, the connection is tight and does not
leak. Do not conduct a leak test using a naked
flame. Porous or damaged hose lines and fittings
must be replaced immediately.

8. Replace the gas cylinder

Important. Refer to the safety information (sections 6.
and 6.1)
1. Select a place away from all sources of ignition.
2. Close the cylinder valve.
3. Undo the union nut on the pressure regulator.
4. Take the pressure regulator off the cylinder.
5. Screw the safety cap into the cylinder valve thread.
6. Connect the new cylinder as described in section 7.

9. Starting up

Notes:
Before starting the device and in particular after
lengthy period of non-use, check the gas supply
parts for blockages caused by insects, etc. If the
gas pipes are blocked, a dangerous flashback
may occur.
Do not start the party radiator until you are
certain that all the gas supply connections are
properly sealed.
Keep a safe distance away from the burner since
a shooting flame may be generated when you
start it caused by a gas accumulation.
To ensure that this does not happen when you
ignite the device, ensure that the regulating knob
is set to minimum (no flame symbol).
1. Open the gas cylinder valve (Fig. 2 / Item 3).
2. Turn the regulating knob to the small flame
symbol, press it down and at the same time
press the piezo ignition repeatedly. Hold the
regulating knob for approx. 10 more seconds
after ignition until the burner remains on. If, in
exceptional circumstances, the device does not
ignite after you have pressed the piezo ignition 3
– 4 times, or the flame goes out, wait for at least
12
06.06.2006 14:03 Uhr Seite 12
two minutes before attempting to start the device
again.
3. Always turn the regulating knob slowly from the
large flame symbol to the small flame symbol.
The device may go out if the knob is turned too
quickly.
4. To turn off the device, close the gas cylinder
valve (3).

10. Shutting down

Close the gas cylinder valve (Fig. 2 / Item 3)

11. Storage / Care / Repair

Remove the pressure regulator with gas hose
and check the gasket for damage. Please contact
ISC GmbH in case of damage.
Never store the liquid gas cylinder inside the
house, under ground or in non-ventilated areas!
The valves on the liquid gas cylinder must have
valve safety caps and locking nuts.
Gas bottles must be stored upright - even if they
are empty.
The party heater can be cleaned with all
standard, non-abrasive and incombustible
liquids.
Be sure to turn off the heater and allow it to cool
before commencing with the cleaning.
Caution! Never clean the heater with
pressurized water (using a water hose, steam jet
or high pressure)!
Have only approved gas fitters carry out repairs
and maintenance work on the party heater.
Only original spare parts should be used for
repairs.
Maintenance: Check the hose lines (gas hose)
at least once per month and every time you
change the liquid gas cylinder. If the hose lines
show any signs of becoming brittle or other
damage, you must replace them with new hoses
of the same length and quality. The device
should be subjected to a maintenance test by a
specialized dealer every 2 years. Any defective
parts must be replaced during this process. We
recommend that the pressure regulator be
replaced after five years, as rubber gaskets and
diaphragms can become porous.