YATO YG-03006 Originalanleitung Seite 9

GB
Check the product for damage. If you find any damages, do not use the product before removing damages or replacing damaged
items for new ones, free from damage.
Wash the product in accordance with the instructions from the point "Product maintenance".
Mount the selected accessory in accordance with its intended purpose. The symbol of an open padlock, which is visible on top
of the accessory adapter should be directed on the arrow symbol visible on the drive. Push, and then turn the accessory so the
arrow will be pointing toward the closed lock symbol.
Make sure, the accessory has been connected correctly and it will not detach itself from the housing drive during operation.
If you use the cutting attachment, it may be used only together with the supplied container. The container should be placed only
on a flat, level and hard surface, before using it, you should remove the attachments handle and make sure that the the container
lid has been completely closed.
Mixing attachment is used for grinding fruit and vegetables, for preparation of sauces, mixing liquids, for example. soups, creams,
etc.
The cutting attachment is used for chopping, grinding of meat and for the preparation of pastes with hard food products.
The compacting attachment is used for preparing a foam of eggs, for cream whipping, mixing rare cakes for example pancakes,
for eggs rubbing.
If the container with the scale, was delivered with the product, it can be used as a vessel for food preparation. It is also possible
to use the public available containers intended for this purpose. The cutting attachment may be used only with the supplied
container with a lid.
Product service
Without touching the switch, you should connect the power cord plug into the mains wall socket.
Enter the end of the attachment to a container with food, and then start the blender by pressing and holding the switch. The
blender is equipped with two switches: the top switch allows to work at a slower speed and the lower switch allows to work at the
maximum speed.
If you use the upper switch you can adjust rotational speed with the control knob. If you use the lower switch the blender only
operates at the maximum speed.
Operation time of the blender may not exceed 30 seconds, after that you should allow the blender to cool down for at least 3
minutes.
The blender is stopped after releasing the pressure on the switch. You should allow to stop for rotation of the moving parts, and
then remove the attachment from the food container, then remove the plug of power cable from the mains wall socket and proceed
to maintenance.
If there are used attachments equipped with blades, at the start of the operation, we recommend that you use a lower speed and
gradually increase it in the course of work, until you achieve satisfactory work effects.
Lower the speed of all attachments will reduce liquid food splattering and spreading of granular products.
Maintenance of the product
ATTENTION! Before each cleaning, turn off the product, disconnect the plug of power cable from the mains wall socket. and then
wait for its cooling down and only then proceed to maintenance.
ATTENTION! We recommend that you clean the blender attachments immediately after food preparation. This will prevent the
food residues caking and will facilitate the cleaning of the product.
If, in the course of work, the driver housing become contaminated with processed food, you should stop working, clean the product
and only after that resume your work.
To clean the product, you should use only mild agents intended to clean kitchen utensils. It is forbidden to use abrasive cleaners for
example powder or cleaner milk, which is containing corrosive substances. Do not use cleaning solvents, gasoline or alcohols.
Cleaner should be diluted with water accordance to the information that came with it, then you should apply it on a soft cloth and
clean the product from inside and outside.
Residues of the cleaning agent should be removed with a soft cloth slightly soaked in clean water. Then dry all the surfaces with
a dry soft cloth.
ATTENTION! The product is not intended for cleaning with a stream of water. Do not immerse the product in water.
By using a stream of water or by immersing in water you may clean the containers with scale and the operational tip of compacting
attachment, after disconnecting it from the adapter which allows for the drive connection. The remaining elements of the product
should be cleaned only with a damp cloth.
The blade and blade guard of the mixing attachment can be cleaned with water after you disconnect the attachment from the drive,
and with care, to avoid the wetting of adapter, which allows for connecting the drive.
Before using the product again, you should dry all elements.
ATTENTION! In the case, when you prepare one dish immediately after the other, during preparation of various dishes using
the same attachment, you can get rid of the food remnants by immersing and short run of the attachment in the container with a
clean, lukewarm water.
When you are cleaning the blades, you should avoid the situation when they contact with a human body. You should wash by
using brushes or sponges.
O R I G I N A L I N S T R U C T I O N S
9