YATO YG-03006 Originalanleitung Seite 8

GB
PRODUCT CHARACTERISTICS
Hand blender is used for food preparation. Due to the mixing attachment, it is possible to prepare food by cutting and mix food
products. If the blender has accessories it is also possible to extend the preparation scope of dishes. Correct, reliable, and safe
operation of the device is dependent on its proper use, therefore:
Prior to working with the product, you should read all the instruction and keep it around.
For any damage caused by failure to comply with safety regulations and instructions of this manual, the supplier is not respon-
sible.
EQUIPMENT
The product is supplied in a complete state but it requires some preparatory steps before starting its operation, described later
in this manual.
The mixing attachment is provided with YG-03006 product.
With the product YG-03006 there are also supplied: mixing attachment, container with the scale, compacting attachment, cutting
attachment along with a container with a lid and a handle, which is allowing to mount the attachments for a storage period.
SAFETY INSTRUCTIONS
Attention! Read all the instructions below. Failure to comply with them can lead to electrical shock, fire or personal injury.
FOLLOW THE FOLLOWING INSTRUCTIONS
Do not use the product in an environment with an increased risk of explosion, containing flammable liquids, gases or vapors.
Before you run the product, you should check whether it, its accessories, and the connection cable are not damaged. If you
noticed any damage is prohibited to started operation of the product. It is forbidden to repair the power supply cable, it should be
replaced with a new one. Any replacement of damaged items including the power cord, should be carried out only in the authorized
facilities, Any independent repair of the product is forbidden.
The product designed for indoors operation only. Do not expose the product to humidity or precipitation. Water and moisture that
gets inside the device increases the risk of electric shock. Do not immerse the product in water or any other liquid.
Connect the unit only to the mains of voltage and frequency shown on the rating plate of the device. Power cord plug must fit into
the wall outlet. It is forbidden to modify the plug. Do not use any adapters in order to adapt the plug to the outlet. The unmodified
plug, which fits the outlet, reduces the risk of electric shock.
After each use, you should disconnect the power cord plug from a mains outlet. Always unplug the blender from the power supply
if it is left unattended and before its assembly, disassembly or cleaning.
Do not overload power cable. Do not use the power cord to carry, plug and unplug the plug from the mains outlet. Avoid contact of
the power cord with heat, oils, sharp edges and moving parts. Damaged cable increases the risk of an electric shock. In the event
of damage to the power cord (e.g., intersection, melting of insulation) you should immediately disconnect the plug from the wall
outlet, and then pass the product to an authorized repairing service. It is forbidden to use the product with a damaged hose. It is
forbidden to repair the power supply cable. the cable must be replaced with a new one at the authorized service point.
Before assembly, disassembly or adjustment of product accessories, you should disconnect the power plug from the wall socket.
Take special care when handling the sharp parts of the product. You should not touch any parts of which are in a motion. The
blades are very sharp, and even in the case of blades, which are still at the moment, there is a risk of injury. You should be very
careful when handling any accessories which are containing blades.
Before starting the product, you should make sure that the selected accessory is correctly mounted.
Do not overload the product. the housing temperature should never exceed 60 C. Overloading of the product will cause its faster
O
wear, and can also cause damage and increase the risk of electric shock.
The product is not intended for use by children. You should keep the cable out of reach of children. Please pay attention, that the
children would not treat the product as a toy.
Children without supervision should not carry out the cleaning and maintenance of the device.
The product is not intended for use by persons with reduced physical capabilities, reduced mental abilities and people with lack of
experience and knowledge of the equipment. unless there is provided the supervision or instruction concerning the use of appli-
ance in a safe way, so that the associated risks would be understood.
PRODUCT SERVICE
Preparing for operation
You should unpack the product, completely removing all the elements of the package. It is recommended to keep the packaging,
may be useful for later transport and storage of the product.
O R I G I N A L I N S T R U C T I O N S
8