Technische Daten - AER Domino 3 Bedienungsanleitung

6. Technische Daten Domino 3, Teil 1
Inputs (notes 1, 2)
Inputs, channels Combo socket, XLR + jack ¼" (6.35 mm)
1 – 4 Line mode
High impedance, unbalanced jack
input for instruments (pick-ups) and
line-level sources
Sensitivity: 26 mV (–32 dBV)
Pad switch (attenuator): –10 dB
Impedance: 1 Meg
Equivalent input noise,
A-weighted: 1.6 µV (–116 dBV)
Phantom power: +9 V DC at ring of jack
sockets in Ch. 1 and Ch. 3, switchable
per channel (note 4), max. 100 mA (all
channels total), overload protected
Mic mode
XLR (balanced), stereo jack (balanced),
or mono jack (unbalanced) input
Sensitivity: 7.5 mV (–43 dBV)
Pad switch (attenuator): –19 dB
Impedance (balanced): 1.7 k
Equivalent input noise,
A-weighted: 0.3 µV (–130 dBV)
Voice filter: –4 dB at 450 Hz
(referred to 10 kHz)
Phantom power: 48 V, with common
on/off
switch for all four channels (note 4)
Clip indicator: Headroom 6 dB
Return Stereo return from external parallel
effect loop
2 x mono jack, ¼" (6.35 mm, left/right
Sensitivity: 375 mV
Routing: stereo to speakers,
headphones, rec out, and L/R-out;
mono (L+R) to DI out
Aux in Auxiliary stereo input (e.g.,
for CD player)
Level adjustable
Cinch (RCA) sockets (left/right)
Sensitivity: 375 mV
Routing: stereo to speakers,
headphones, rec out, and L/R out;
mono (L+R) to DI out
Outputs (note 3)
Tuner
Tuner output, not affected by
mute switch
Mono jack, ¼" (6.35 mm)
Output voltage: 360 mV
Headphones Headphones output. When connected,
internal speakers are muted.
Stereo jack, ¼" (6.35 mm)
Output power:
max. 2 x 100 mW / 32 ohms
Input sensitivity for
2 x 50 mW / 32 ohms:
30 mV at line input (any channel)
12
Caution: For stereo headphones with
stereo jack plug only.
Do not connect mono plugs.
Active speaker Mono (L+R) output post-master,
suitable for active extension speaker
Mono jack, ¼" (6.35 mm)
Output voltage: 1.4 V
Activates 100 Hz low-cut filter for
internal speaker if plugged in.
L/R-out Stereo line output after tone controls,
with aux in and effects
Level adjustable by pre out
2 x mono jack, ¼" (6.35 mm, left/right)
Output voltage: 0...1.4 V
Rec out Recording output after tone controls,
with aux in and effects
Cinch (RCA) sockets (left/right)
Output voltage: 1.4 V (note 4)
DI Balanced XLR output before master,
after tone controls, with aux in and
effects (note 4)
Level adjustable
Output voltage: 0...145 mV
Send Send for parallel effect loop
Mono jack, ¼" (6.35 mm)
Output voltage: 710 mV (note 4)
USB lamp
DC output for a lamp
Data lines are not connected.
Output voltage: 5 V DC, max. 200 mA
Insert points
Insert L/R
Stereo insert point after master volume
2 x stereo jack (L/R), ¼" (6.35 mm)
Tip = send, ring = return
Output voltage: 1.4 V
Tone controls (all channels)
colour +10 dB at 8 kHz, –3 dB at 700 Hz
bass ±8 dB at 100 Hz, shelf type
middle
±4 dB at 650 Hz
treble ±9 dB at 10 kHz, shelf type
Effects
Internal effect AER 32-bit digital effect processor
with 16 factory presets
Two independent, simultaneous
effects (one for channels 1 and 2, and
one for channels 3 and 4).
USB interface and PC software for
creating userdefined settings
External effect
Parallel effect loop
(see send and return)