Herunterladen Diese Seite drucken

CALECTRO UNIGUARD SUPERFLOW UG-3-A4O Installationsanleitung Seite 2

Werbung

Bohren Sie ein Loch in den Kanal:
• Ohne UG-Halterung: ø 38 mm.
• Mit UG-Halterung und/oder Venturirohr mit
Zusatzgebläse: ø 51 mm (siehe Absatz 10).
• Messen Sie den Kanaldurchmesser.
• Kürzen Sie das Rohr bei Bedarf.
• Das Rohr sollte mindestens 90 % des
Kanaldurchmessers durchdringen.
HINWEIS: Siehe Absatz 8.
• Stecken Sie den Rohrverschluss ein.
• Setzen Sie die schwarze Dichtung auf
das Rohr.
• Schieben Sie das Rohr von unten in den
Uniguard-Rauchmelder.
• Befestigen Sie das Rohr mit der
Sicherungsschraube.
• Montieren Sie Rohr und Rauchmelder im
Kanal.
• Sichern Sie die Unterseite des Uniguard-
Rauchmelders mit den drei Schrauben
(Positionen mit Pfeilen gekennzeichnet).
HINWEIS - WICHTIG:
Die Richtungspfeile für den Luftstrom
(siehe Form der Unterseite des
Uniguard-Rauchmelders oder Oberseite
des Gehäuses) müssen in die Richtung
des Luftstroms im Lüftungskanal zeigen.
Luftstromanzeige und Rohr mit
Zusatzgebläse*.
Der Uniguard-Rauchmelder verfügt über eine
Anzeige, eine Kunststoff "Zunge", die bei
korrektem Einbau durch den Luftstrom nach
außen gebogen wird.
HINWEIS:
Wenn sich die Anzeige nicht bewegt, sollten Sie
den Uniguard-Rauchmelder entweder an einer
anderen Stelle anbringen, oder ein Venturirohr
mit Zusatzgebläse installieren.
Bei der Installation eines Venturirohrs mit
Zusatzgebläse wird immer eine Montagehalterung
verwendet.
* Ein Zusatzgebläserohr ist ein Venturi-Standardrohr
mit einem Zusatzgebläse, das eine separate
24 V AC-Stromversorgung benötigt.
Elektroinstallation.
• Entfernen Sie das Gehäuse, indem Sie den
Schnappverschluss über die Leiterplatte
öffnen.
• Führen Sie das Kabel durch eine der
Klikseal-Kabeldurchführungen. Wenn Sie
einen anderen Kabeldurchführungstyp für
die Kabel verwenden, entfernen Sie die
installierten Kabeldurchführungen, indem Sie
zunächst eine Seite und dann die andere
Seite durch die Öffnung schieben (1-2).
Diese Seite NICHT abkürzen!
Do NOT cut this end!
3
Sicherungsschraube.
Locking screw.
5
Luftstromanzeige.
Flow indicator.
Venturirohr mit Zusatzgebläse.
Venturi pipe with booster fan.
6
Schnappverschluss.
Snap locking.
(1)
(2)
1
Drill a hole in the duct:
• Without UG-bracket, ø 38 mm.
• With UG-bracket and/or venturi pipe with booster
fan, ø 51 mm (see para 10).
2
• Measure the diameter of the duct.
• Shorten the pipe, if necessary.
• The pipe should penetrate at least 90%
• Insert the end plug.
Rohrverschluss.
End plugg.
• Mount the black gasket on the pipe.
• Insert the pipe into the bottom of the
• Secure the pipe with the locking screw.
Dichtung.
Gasket.
4
• Mount the pipe and the detector on the
• Secure the bottom of the Uniguard with
Flow indicator and booster fan pipe*.
The Uniguard is supplied with an indicator,
a plastic "tongue", which – when the
detector is correctly installed – is bent
outwards due to the airflow.
NOTE!
If the indicator does not move, you should
consider a new mounting positioning of the
Uniguard or install a booster fan venturi pipe.
With installation of a booster fan venturi pipe
a mounting bracket is always used.
* A booster fan pipe is a standard venturi pipe including a
Rück.
Electrical installation.
Reset button.
• Remove the cover over the printed circuit
• Enter the cable through one of the
of the width of the duct.
NOTE! See para 8.
Uniguard.
duct.
the 3 screws, positions marked.
NOTE - IMPORTANT!
The air flow direction arrows (see
the Uniguard foot's shape or on the
housing top) must have the same
direction as the air flow in the duct.
booster fan, which needs separate 24 VAC supply.
board by opening the snap locking.
Klikseal glands.
When using another type of cable gland
dismount the ones already installed by
first pressing one side through the hole
and then the other one (1-2).

Werbung

loading

Diese Anleitung auch für:

Uniguard superflow ug-3-a5o