Operation - Monacor LEDS-5RF/RGB Anleitung

LED Light Strip with Remote Control
GB
Please read these operating instructions carefully prior
to operation and keep them for later reference.
1 Applications
This 5 m LED light strip with 150 RGB LEDs is used for
decorative lighting. A user-friendly wireless remote
controller allows to adjust the lighting colour and the
brightness of the LEDs and to select various light pro-
grams. The operating range is approx. 20 m.
2 Important Notes
The components of the LED set (controller, remote
controller, LED light strip and power supply unit) corre-
spond to all relevant directives of the EU (marking
WARNING
The power supply unit uses dangerous
mains voltage. Leave servicing to skilled
personnel only. Inexpert handling of the
unit may result in electric shock.
G
The LED set is suitable for indoor use only. Protect
it against dripping water and splash water, high air
humidity and heat (admissible ambient temperature
range: 0 – 40 °C). However, the LED strip is mois-
ture-proof (IP 65) and therefore also suitable for
damp locations.
G
Do not operate the controller and immediately dis-
connect the power supply unit from the socket
1. if the power supply unit, the controller or the LED
strip is visibly damaged,
2. if a defect might have occurred after a unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the LED set must be repaired by skilled
personnel.
G
For cleaning only use a dry, soft cloth; never use
water or chemicals. However, you may wipe the LED
strip with a damp cloth.
G
No guarantee claims for the individual components
and no liability for any resulting personal damage or
material damage will be accepted if the LED set is
used for other purposes than originally intended, if it
is not correctly connected or operated, or if it is not
repaired in an expert way.
If the LED set is to be put out of operation de-
finitively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
2.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL declare that
the wireless remote controller of the set LEDS-5RF/
RGB is in accordance with the basic requirements
and the other relevant regulations of the directive
1999/ 5 / EC. The declaration of conformity is available
1
2
3
4
5
6
7
8
LEDS-5RF/RGB
on request from MONACOR INTERNATIONAL. The
wireless remote controller is licence-free and gener-
ally approved for operation in EU and EFTA countries.
3 Putting the LED Strip into Operation
3.1 Installation
1) If required, cut the LED strip to length where a scis-
sor symbol is shown. To attach the LED strip, it is
provided with a self-adhesive back. Furthermore, it
is supplied with 10 retaining clips.
2) Connect the LED strip to the luster terminal (9) of
the cable OUTPUT from the controller:
Connector of LED strip
). B (blue)
G (green)
R (red)
+12 V
3) Connect the power supply unit provided to the jack
INPUT (11) and to a mains socket (230 V~ / 50 Hz). If
you do not use the LED set for a longer period of
time, disconnect the power supply unit from the
mains socket; otherwise the controller and the
power supply unit will have a low power consump-
tion, even with the LEDs switched off.
3.2 Inserting / Replacing the batteries
To insert/replace the batteries, remove the cover of the
battery compartment on the rear side of the remote
controller. Insert three batteries of size AAA as indi-
cated in the compartment. Then close the cover.
To prevent damage to the remote controller due to
battery leakage, always remove the batteries if you do
not use the remote controller for a longer period of
time.
Used batteries must not be placed in the
household waste. To protect the environment,
always take them to a special waste disposal,
e. g. collection container at your retailer.

4 Operation

All settings are made via the wireless remote con-
troller. It is provided with touch-sensitive buttons. At
the touch of a button, the indicating LED (8) lights up.
To switch on the LEDs connected, touch the button
(1); to switch them off, touch the button
4.1 Selecting colour and brightness
1) To set the lighting colour, slide your finger around
the colour ring (5) or touch the desired colour.
2) To decrease the brightness, touch the button
to increase the brightness, touch the button
The three indicating LEDs (10) on the controller light
up according to the setting made. Their brightness in-
dicates the control voltages for the LED strips con-
nected.
B
G
R
+12V
9
®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright © by MONACOR INTERNATIONAL. All rights reserved.
Order No. 38.6340
for connection to
blue core
green core
red core
black core
(2).
(7);
(6).
B B
G G
R R
+12V +12V
10 11
4.2 Selecting a light program
No. Function
1 always red
2 always green
3 always blue
4 always yellow
5 always purple
6 always cyan
7 always white
8 change between red, green and blue
9 change between 7 colours
10 fade-in / fade-out of red, green and blue
11 crossfading between red, green and blue
12 fade-in / fade-out of 7 colours
13 crossfading between 7 colours
14 flashing, alternating between red, green and blue
15 flashing, alternating between 7 colours
16 bursts of flashes, alternating between red, green and blue
17 bursts of flashes, alternating between 7 colours
18 automatic change of program
1) Use the button (3) to select light programs in
ascending order and the button
in descending order.
2) Use the buttons (6) and (7) to set the bright-
ness for the programs 1 – 7 and the speed for the
programs 8 – 18 (button to increase the speed;
button to decrease the speed).
3) To exit the light program, touch the colour ring (5).
5 Specifications
Controller
Power supply: . . . . . . . 12 V , 3 A via PSU provided
and connected to
230 V~ / 50 Hz
Dimensions: . . . . . . . . 90 × 28 × 70 mm
Weight: . . . . . . . . . . . . 110 g
Remote controller
Power supply: . . . . . . . 3 × battery size AAA
Transmission
frequency: . . . . . . . . . 433.92 MHz
Operating range: . . . . 20 m
Dimensions: . . . . . . . . 56 × 23 × 114 mm
Weight: . . . . . . . . . . . . 64 g
LED light strip
Number of LEDs: . . . . 150 RGB LEDs
Beam angle: . . . . . . . . 120°
Protection: . . . . . . . . . IP 65
Dimensions: . . . . . . . . 10 × 3 × 5000 m
Subject to technical modification.
1 To activate the LEDs
2 To deactivate the LEDs
3 Light programs 1 © 18
4 Light programs 18 © 1
5 Colour ring to set the lighting colour
6 To increase brightness / speed
7 To decrease brightness / speed
8 Indicating LED, lights up at the touch of a button
9 Terminal to connect the LED strip
10 Indicating LEDs, their brightness indicates the
control voltages for the LED strip
11 Jack INPUT for the power supply unit provided
A-1384.99.01.11.2012
(4) to select them