Denon DRR-201SA Bedienungsanleitung Seite 12

ENGLISH
(5) Timer functions (when connected to the PMA-201SA and TU-201SA)
The timer functions of the tuner (TU-201SA) can be used to play cassette tapes or record radio programs ("Air
2
Check") at set times.
• Refer to the operating instruction included with the TU-201SA.
(6) Editing functions (when connected to the PMA-201SA and DCD-
201SA)
Use this function to automatically edit the tracks on the CD to fit on the tape to be used for recording.
2
The editing function is set from system remote control unit (RC-906) included with the pre-main amplifier (PMA-
2
201SA).
PMA-201SA (pre-main amplifier)
™ ON / STANDBY ¡ OFF MODE
PHONES FUNCTION
1
DRR-201SA (this unit)
2 2
ON / STANDBY 5
L
dB -60 -40 -30 -20 -12 -6 -2 0
R
3 DOLBY NR B
DCD-201SA (CD player)
3 3
C
ON / STANDBY 5
TRACK INDEX TIME
M S
RC-906 (system remote control unit)
OFF ON
SYSTEM
POWER
PROG /
DIRECT
1 2 3
CALL
4 5 6
CLEAR
7 8 9
RANDOM REPEAT
10 +10
CD SRS
CD-R TAPE MD TIME EDIT
REV. TIME/
Dolby NR DIMMER
MODE PANEL
12
Downloaded from www.Manualslib.com
Turn on the power of the pre-main amplifier.
• The system's power turns on.
VOLUME
SOURCE DIRECT
1
™ ON / STANDBY ¡ OFF
INTEGRATED AMPLIFIER PMA-201SA
(PMA-201SA)
Load the cassette tape onto which
2
you want to record into the DRR-
201SA's cassette holder.
1 2
DOLBY REVERSE 4 REC
NR / RESET CD SRS / REC MUTE
3
Load the CD in the DCD-201SA.
REC LEVEL / 0 1
8 9
6 7
+
STEREO CASSETTE TAPE DECK DRR-201SA
Now operate as described in the "Editing
4
Function" section of the operating instructions
included with the CD player (DCD-201SA).
1 3 2
8/6 7/9
COMPACT DISC PLAYER DCD-201SA
1
manuals search engine
NOTES:
• The editing function will not work with discs containing more than 21 tracks.
• Load the cassette tape onto which you want to record into the cassette deck's cassette tray with side A facing up
before starting edited recording. The beginning of the tape is automatically found before recording starts.
• When using a recorded cassette tape for edited recording, recording stops and a blank section is left on side B of
the tape if the tape is longer than the set time, so erase the tape beforehand.
• When the editing function is used for recording, the reverse mode is automatically set to
deck's reverse mode switch is set to
recording on side A is completed.
• In some cases it may not be possible to record all the tracks on the disc, even if the tape is longer than the disc's
recorded time (because of how the tracks are divided onto sides A and B of the tape). The "OVER" indicator on
the CD player flashes if there are tracks that cannot be recorded.
• The jog dial ( 7
selector button (REVERSE MODE) stop button (
• When recording using the editing function, the CD player's auto space function is activated and blank spaces of
approximately 4 seconds are automatically created between tracks. Because of this, when recording CDs
containing for example recordings of concerts without spaces between tracks, blank spaces will be created in the
ON
SYSTEM middle of the piece. In this case, do not record using the editing function.
POWER
• To cancel the editing mode, press the stop button (
CD. The editing mode is not canceled if other buttons are pressed.
(System remote control unit)
5
(Main unit)
5
(Main unit)
, and recording continues on side B after
/ 9 and 8 / 6 ), recording/recording mute button (
) will not function during editing.
2
) on the DRR-201SA or the CD player to stop playback of the
2
even if the cassette
4 REC/REC MUTE) and reverse mode