Sabiana Maestro MTL-ECM 14 Handbuch Für Installation, Gebrauch Und Wartung Seite 35

> 3 sec.
THERMOSTAT PARAMETERS – Only for T–MB and T–MB ± 3°C versions
F
UNCTION
OFS
dEds
dEdr
IrL
F
UNCTION
dS
F
UNCTION
T2-1
T2-2
F
UNCTION
T3-1
T3-2
I-T3
F
UNCTION
t1ds
Decompensation air probe T1 winter cycle (only for Cassette)
F-t1
F-t2
F-t3
F
UNCTION
Slu1
SCu2
SHu3
LLSI
HLSI
LLSE
HLSE
PFC
PFH
F
UNCTION
Pt1
Pt2
Pt3
F
UNCTION
rE-t
D
ESCRIPTION
Thermostat NTC probe offset variation
Dead area central point
Dead area setting field
Relay hysteresis
THERMOSTAT PARAMETERS – Only for T–MB ± 3°C version
D
ESCRIPTION
Set variation range with T–MB
PARAMETERS of the T2 probe, CHANGE-OVER
D
ESCRIPTION
Status changeover from ventilation to cooling
Status changeover from ventilation to heating
PARAMETERS of the T3 probe, TME minimum probe
D
ESCRIPTION
Fan ON in heating mode
Fan ON in cooling mode
T3 probe hysteresis
PARAMETERS of the Stratification Cycle
D
ESCRIPTION
Fan OFF time
RL2 ON time
Post ventilation time
THERMOSTAT PARAMETERS – Only for T–MB–ECM version
D
ESCRIPTION
Speed min. voltage
Speed medium voltage
Speed max. voltage
Speed min. voltage for winter auto fan
Speed max. voltage for winter auto fan
Speed min. voltage for summer auto fan
Speed max. voltage for summer auto fan
Cooling proportional band
Heating proportional band
PARAMETERS of the Pump Timer
D
ESCRIPTION
Pump intervention delay time
OFF time during Summer
ON time during Summer
OTHER FUNCTIONS
D
ESCRIPTION
General reset and restore of default values
19
FEATURES FOR FACTORY
This menu allows modifying the operation
parameters of the thermostat, electronic motor, of the +/- 3 version
and many other parameters (pump cycle, RESET).
With the control set on "OFF", press
the M and Fan buttons simultaneously for 3 seconds.
Select the desired parameter to be modified,
pressing button "+" or "-" and confirm using the "M" button.
Once the parameter is selected, the value will be displayed.
The value can be modified using button "+" or "-".
Press the "M" button once to turn back to the parameter selection;
to exit the menu, press the "M" button for more than 5 seconds.
R D
ANGE EFAULT
± 3°C 0°C
18 ÷ 30°C 22°C
1 ÷ 6°C 2°C
0,5 ÷ 2,0°C 0,7°C
R D
ANGE EFAULT
± 9°C ± 3°C
R D
ANGE EFAULT
15 ÷ 25°C < 22°C
25 ÷ 35°C > 32°C
R D
ANGE EFAULT
> 30 ÷ 40°C > 36°C
< 10 ÷ 25°C < 22°C
2 ÷ 6°C 4°C
R D
ANGE EFAULT
0,5 ÷ 2,0°C 1,5°C
5 ÷ 13 min. 10 min.
30 ÷ 120 sec. 40 sec.
5 ÷ 240 sec. 60 sec.
R D
ANGE EFAULT
1 ÷ 6 1 V
3 ÷ 8 5 V
6 ÷ 10 10 V
1 ÷ 6 1 V
5 ÷ 10 10 V
1 ÷ 6 1 V
5 ÷ 10 10 V
2,0 ÷ 6,0 3,5°C
2,0 ÷ 6,0 3,5°C
R D
ANGE EFAULT
0 ÷ 300 sec. 150 sec.
30 ÷ 90 min. 60 min.
0 ÷ 5 min. 3 min.
O
PERATION
Confirmation with O/I and Fan buttons
T-MB