VOLTCRAFT 1603380 Bedienungsanleitung Seite 2

Operating Instructions
USB Wall Plug Transformer SPAS-2100 SE
Item no. 1603380
Intended use
The product is used to provide power or to charge end devices via a standard USB connection.
The current circuit of the connected load must not exceed the output current of the wall plug
transformer.
Always observe the safety instructions and all other information included in these operating
instructions.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package content
• USB wall plug transformer
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website
Explanation of symbols
The symbol with the lightning bolt indicates that the product is connected to the
mains voltage.
In the operating manual, an exclamation mark inside a triangle indicates important
instructions.
Safety instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! In such
cases, the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is not permitted
for safety and approval reasons. Never dismantle the product.
• The product is not a toy. Devices operated using mains voltage do not belong in
the hands of children. Therefore, be especially careful when children are around.
Use the product where it is out of the reach of children.
• The product is intended for use only in dry, indoor locations. The product must
not become damp or wet; never handle it if your hands are wet! There is a
lifethreatening hazard through an electric shock!
• Use only a standard mains socket as the power source for the USB wall plug
transformer.
The mains socket into which USB the wall plug transformer is plugged must be
easily accessible.
• Never use the product immediately after it has been taken from a cold room to a
warm one. The condensation that forms might damage the product under certain
circumstances. Furthermore, this could cause a lethal electric shock!
Allow the product to reach room temperature before connecting it to the power
supply and putting it to use. This may take several hours.
• Avoid the following adverse conditions at the installation location and during
transport:
- Excessive humidity or dampness
- Extreme cold or heat, direct sunlight
- Dust or flammable gases, fumes or
- solvents
- Strong vibrations, impacts or blows,
- Strong magnetic fields such as those found in the vicinity of machinery or
loudspeakers
• Do not pull the USB wall plug transformer from the mains socket by pulling on
the USB cable connected. Hold it on the sides of the casing and pull it out of the
mains socket.
• When using the product, make sure that suffi cient air circulation is ensured and
do not cover the product.
• Always place the cable carefully so that nobody can trip over it. Risk of injury.
• Never pour liquids on electrical devices, and never place any liquid-containing
objects (such as vases) on top of them or near them. You run the risk of causing
a fi re or a fatal electric shock.
• If the USB wall plug transformer is damaged, do not touch it; there is a
lifethreatening electric shock hazard!
First, switch off the mains voltage to the socket to which the USB wall plug
transformer is connected (switch off at the corresponding circuit breaker or
remove the safety fuse or switch off at the corresponding RCD protective switch,
so that the socket is fully disconnected).
You can then unplug the USB wall plug transformer from the mains socket.
Dispose of the faulty wall plug transformer in an environmentally friendly way, do
not use it any more.
• Do not leave the packaging material carelessly lying around, since it could become
a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
Getting started
• Connect a USB cable to the connection on the wall plug transformer.
Important! The permanent output voltage of 5 V/DC of the wall plug transformer
must correspond to the input voltage of the electrical load that is connected to the
wall plug transformer.
If this is not observed, both the connected load and the transformer may be
damaged, resulting in loss of warranty!
• Plug the wall plug transformer into a standard mains socket.
• If the load has an on/off switch, switch the load on now. If the load does not function correctly,
switch it off immediately and check the correct cable connection.
• In spite of the low standby power input, it is recommended to disconnected the USB wall plug
transformer from the mains socket if you don't use it any longer.
Maintenance and cleaning
The USB wall plug transformer does not require any maintenance and should never be
disassembled for any reason.
Pull the wall plug transformer from the mains socket before cleaning. Use a clean, dry, soft
cloth for cleaning. Do not use aggressive cleaning agents, as these can cause discolouration.
Do not press too strongly on the surface when cleaning, to prevent scratch marks.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Operating voltage ......................... 100 - 240 V/AC, 50/60 Hz
Output voltage .............................. 5 V/DC
Output current ............................... 2.1 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1603380_v1_0917_02_jh_m_en_(1)