2LS Tools VEGA Originalbetriebsanleitung Seite 23

Downloaded from www.Manualslib.com
OBJ_BUCH-1618-001.book Page 23 Thursday, February 16, 2012 2:01 PM
a) Indirect height measurement (see figure C)
Press the function-mode button 4 until the indication
for indirect height measurement
1
display.
Pay attention that the measuring tool is positioned at
the same height as the bottom measuring point. Now,
tilt the measuring tool around the reference plane and
measure distance "1" as for a length measurement.
Upon completion of the measure-
ment, the result for the sought dis-
tance "X" is displayed in the result
line c. The measuring values for the
distance "1" and the angle " α " are
displayed in the measured-value
lines a.
b) Double indirect height measurement
(see figure D)
Press the function-mode button 4 until the indication
for double indirect height measurement
on the display.
Measure distances "1" and "2" in this sequence as
for a length measurement.
Upon completion of the measure-
ment, the result for the sought dis-
tance "X" is displayed in the result
line c. The measuring values for the
distances "1", "2" and the angle " α "
are displayed in the measured-value
lines a.
Pay attention that the reference plane of the measure-
ment (e.g. the rear edge of the measuring tool) re-
mains exactly at the same location for all individual
measurements within a measuring sequence.
c) Indirect length measurement (see figure E)
Press the function-mode button 4 until the indication
for indirect length measurement
1
display.
Pay attention that the measuring tool is positioned at
the same height as the sought measuring point. Now,
tilt the measuring tool around the reference plane and
measure distance "1" as for a length measurement.
Upon completion of the measure-
ment, the result for the sought dis-
tance "X" is displayed in the result
line c. The measuring values for the
distance "1" and the angle " α " are
displayed in the measured-value
lines a.
Wall Surface Measurement (see figure F)
The wall surface measurement is used to determine
the sum of several individual surfaces with a common
height.
2 609 140 906 • 16.2.12
manuals search engine
In the example shown, the total surface of several
walls that have the same room height A, but different
lengths B, are to be determined.
appears on the
For wall surface measurements, press the function-
mode button 4 until the indicator for wall surface
measurement
Measure the room height A as for a length measure-
ment. The measured value ("cst") is displayed in the
top measured-value line a. The laser remains switched
on.
1 appears
2
with the stored height A. The total surface value is dis-
played in the result line c.
In this manner, you can measure any number of further
lengths B , which are automatically added and multi-
X
plied with height A.
The condition for a correct area/surface calculation is
that the first measured length (in the example the room
height A) is identical for all partial surfaces.
Grade measurement (see figure G)
After pressing the grade measurement button 3, the
indication for grade measurement appears on the
display . The backside of the measuring tool is
appears on the
used as the reference plane. By pressing the grade
measurement button 3 again, the side surfaces of the
measuring tool are used as reference plane and the
display view is shown turned by 90°.
Press the measuring button 2 to lock the measuring
value and accept it in the measured values memory.
Pressing the measuring button 2 again continues the
measurement.
When the indication flashes during the measuring
procedure, then the measuring tool was tilted too
much in lateral direction.
If the "digital vial" function is activated in the basic set-
tings, the grade value is also displayed in the other
measuring functions in line d of display 1.
Timer function
The timer function is helpful, when, for example, move-
ments of the measuring tool during measuring are to
be prevented.
appears on the display.
Afterwards, measure length B of the
1
first wall. The surface is automatically
calculated and displayed in the result
line c. The length measurement value
is displayed in the centre measured-
value line a. The laser remains
switched on.
Now, measure length B of the sec-
2
ond wall. The individually measured
value displayed in the centre meas-
ured-value line a is added to the
length B . The sum of both lengths
1
("sum", displayed in the bottom
measured-value line a) is multiplied
English | 23