Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATING INSTRUCTIONS
USB POWER CONVERTER/CHARGER
ITEM NO.: 1270362
INTENDED USE
This USB converter is designed to charge mobile devices (e.g. tablets, iPad etc.) on standard
USB ports on PCs or laptops. When using standard USB ports, the charging current may
decrease over the course of the charging process, or charging may not be possible due to an
insufficient charging current. The USB converter can increase the charging current to up to
2.1 A (depending on the maximum power of the USB port on your PC or laptop).
The product must not come into contact with moisture, e.g. in a bathroom, or with rain and
other similar liquids.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may be
damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric
shock etc. Read the instructions carefully and keep them. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
DELIVERY CONTENT
• USB power converter
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Never pour any liquids over electrical devices or put objects filled with liquid right
next to the device. If liquids or objects do get into the device interior, the product
must not be used any more; take the product to a repair centre.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. Allow the
product to reach room temperature before connecting it to the power supply and
putting it to use. This may take several hours.
• Never leave the product and the connected device unattended during use.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
If you are not sure about the correct connection or use, or if questions arise which are not
covered by these operating instructions, please do not hesitate to contact our technical
support or another qualified specialist.
OPERATION
Ensure that the connection specifications for your mobile device comply
with the connection data for the product (see technical data).
Always read the operating instructions for your mobile device.
Do not short-circuit the USB output.
The product is not designed for data transfer.
• Remove the protective cap on the side of the USB converter marked with USB IN.
VERSION 12/14
• Insert the USB converter into an available USB port on your PC or laptop. The USB
converter lights up red when the USB port is ready.
• Connect the mobile device that you want to charge to the USB-A port (USB OUT) on the
USB converter. Charging begins as soon as a current flows.
• The USB-A port on the USB converter delivers a maximum charging current of 2.1 A.
• Monitor the charging process of your mobile device.
MAINTENANCE AND CLEANING
Never use aggressive detergents, rubbing alcohol or other chemical
solutions, as these could damage the housing or even impair the
functioning of the product.
• Disconnect the USB cable and any connected mobile devices from the product before
cleaning.
• Do not immerse the product in water.
• Under no circumstances should you service any of the components in the interior of the
product, therefore never open/dismantle it.
• A dry, soft and clean cloth is sufficient for cleaning. Do not press too hard on the housing as
this can lead to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TECHNICAL DATA
Input voltage / current ...........................5 V/DC, max. 2.1 A
Output voltage / current ........................5 V/DC, max. 2.1 A
Operating/storage conditions ................-20 to +80 °C, 5 - 90 % RH
Dimensions (W x H x D) .......................45.5 x 18.5 x 11 mm
Weight ..................................................9 g
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the
time of printing.
© Copyright 2014 by Conrad Electronic SE
V1_1014_02-DS
Werbung
