Working Instructions; Accessories - Felisatti JSF100/650VE Bedienungsanleitung

PROTECTIVE COVERS FOR CLEAN CUTS
Anti-splinter plate K prevents the surface from splinter-
ing when wood is being sawed.
Position anti-splinter plate K as shown in Fig.4 with the
fittings downwards.
To install the sliding skid, clip it onto the front of
support base L as shown in Fig.7. Press the rear
section upwards until it is locked in place as shown
in Fig.8.
WARNING! The anti-splinter plate cannot be used with
certain types of saw blade (for example, jump saw
blades).
Support base L which is fitted with a steel insert pro-
vides a high degree of stability and may be used with-
out sliding skid J to work on metal or other non-delicate
surfaces.
It is recommended that sliding skid J is used with
material that is easily scratched in order not to damage
delicate surfaces.
DUST EXTRACTION
WARNING! Always make sure that the tool is switched
off and unplugged before fitting or removing any dust
extraction device.
Dust extraction keeps the workplace clean, prevents
dust build-up in the air and facilitates waste elimination.
CAUTION! During prolonged operations with wood or
in professional applications with materials that produce
harmful dust, a suitable external aspirator must be
connected.
These jig saws are fitted with adapter M which can be
coupled to a universal vacuum aspirator or other dust
extraction device.
Installing the dust suction adapter
To install adapter M, it should be inserted into support
base L from the rear of the guide and pushed down-
wards until it locks in place (Fig.6). It can be removed
by pressing lower adapter tab N and pulling it back-
wards until it comes out of support base L.

WORKING INSTRUCTIONS

During sawing operations, base plate L must be com-
pletely supported on the surface. It is possible to cut
wood without having made a previous drill hole, allow-
ing the blade to slowly penetrate into the material with
the machine in operation. However, this does require a
certain amount of experience.
Support the front edge of base plate L inclining the
machine upwards and switch it on. Support the ma-
chine firmly against the work-piece and slowly lower it
so that the saw blade penetrates the work-piece.
Once the material has been cut through, place the
machine into its normal operating position so that the
base plate is seated on its entire surface area and
continue the sawing operation according to require-
ments.
When sawing is completed, first switch the machine off
and then remove the blade from the saw slot.

ACCESSORIES

Accessories and their corresponding order number can
be found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying
out work on it.
- Saw blade inspection: Only sharp blades in perfect
condition should be used. Cracked, bent or jagged
saw blades should be immediately replaced.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tight-
ened. Should any screw be loose, tighten it immedi-
ately. Failure to do so could put you at serious risk.
- Motor maintenance: Always take the greatest care
over this and make sure that the motor winding is not
damaged and/or becomes wet with oil or water.
- Always keep the vents clean and free of obstruction.
- Clean the machine thoroughly after each use. Blast
the motor regularly with compressed air.
- The saw blade retaining lever ("Quick Fix" systems)
must be regularly cleaned, especially when sawing
material which produces large amounts of dust. This
will ensure correct retaining lever operation.
- The saw blade guide should be lubricated now and
again with a drop of oil and, at the same time,
checked for wear. If it is worn, after prolonged use, it
should be replaced at the Felisatti Technical Assis-
tance Centre.
- Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it
replaced.
- Brush replacement: The brushes should be re-
placed after 150-200 hours use or when they are
less than 10 mm long. Have this done by an Official
Service Centre. We recommend that on every other
change of brushes, you take the machine to one of
our Official Service Centres for general cleaning
and oiling.
- Use only Felisatti accessories and spares. The parts
the changing of which is not covered in this instruc-
tion manual, should be replaced in a Felisatti Official
Service Centre (See Warranty/Official Service Centre
address leaflet).
Do not dispose of electric tools in
the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
WARRANTY
See general warranty conditions printed on the at-
tached sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise
to a minimum. However, in spite of this, in certain
circumstances the maximum noise level in the
place of work could exceed 85 dBA. In this case,
the operator should wear ear protection.