Specifications - Maktec MT372 Betriebsanleitung

ENGLISH
1 Base
2 Scale
3 Bit protrusion
4 Clamping screw
5 Switch lever
6 Loosen
7 Tighten
8 Hold
9 Workpiece
10 Bit revolving direction
11 View from the top of the tool

SPECIFICATIONS

• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
TRIMMER SAFETY WARNINGS
1. Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
Downloaded from www.Manualslib.com
(Original instructions)
12 Feed direction
13 Straight guide
14 Clamping screw (A)
15 Adjusting screw
16 Clamping screw (B)
17 Trimmer guide
18 Chip deflector
19 Guide holder
20 Screwdriver
21 Base protector
22 Screws
Model
Collet chuck capacity
–1
No load speed (min )
Overall length
Net weight
Safety class
manuals search engine
Explanation of general view
3. Wear hearing protection during extended period
of operation.
4. Handle the bits very carefully.
5. Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
ENE010-1
6. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7. Hold the tool firmly.
8. Keep hands away from rotating parts.
9. Make sure the bit is not contacting the work-
ENF002-2
piece before the switch is turned on.
10. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
11. Be careful of the bit rotating direction and the
feed direction.
12. Do not leave the tool running. Operate the tool
only when hand-held.
GEA010-1
13. Always switch off and wait for the bit to come to
a complete stop before removing the tool from
workpiece.
14. Do not touch the bit immediately after operation;
it may be extremely hot and could burn your
skin.
15. Do not smear the tool base carelessly with thin-
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
GEB019-4
16. Use bits of the correct shank diameter suitable
for the speed of the tool.
17. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
18. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
23 Bit
24 Templet
25 Templet guide
26 Bolt
27 Guide plate
28 Wing nut
29 Center hole
30 Nail
31 Guide roller
32 Limit mark
33 Brush holder cap
MT372
6.35 mm (1/4") or 6.0 mm
35,000
199 mm
1.4 kg
/II
5