Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
(63).
O
UTPUTS
30. M
(32): This switch toggles whether the
O
S
ONO
UTPUT
WITCH
(59, 60) will be in Mono or Stereo.
M
O
ASTER
UTPUTS
31. A
(33): This button controls the BPM
BPM/T
B
UTO
AP
UTTON
detection engine. By pressing and holding this button for 1 sec-
onds, the unit will attempt to automatically detect the beats per
minute of the audio channel which is selected via the C
(13). If there is no channel selected, the unit will attempt to
B
UTTON
detect the BPM of the Master signal. If the unit is not able to accurately
detect the BPM, you may tap the A
BPM/T
UTO
music until the correct BPM is displayed on the LCD P
(36). To show the BPM at any time, press the A
momentarily, and it will again be displayed on the LCD P
(36). When the letters 'A BPM' are displayed with the beats per minute, it
indicates that the value displayed was automatically detected. When the
letters 'T BPM' are displayed with the beats per minute, it indicates that
the value displayed was calculated via the TAP function.
32. EFX-T
S
O
/O
(34): When this feature is turned on,
EMPO
YNC
N
FF
any effects that can be synchronized to tempo will be linked to the
tempo that is set via the A
BPM/T
UTO
AP
33. T
R
S
(35): This selector controls the ratio of
EMPO
ATIO
ELECTOR
the tempo that is set via the A
UTO
the control is set to any other value other than 1 (1:1 ratio), the
tempo will be multiplied by that value. For instance, if a track is 125 beats
per minute, then switching the T
R
EMPO
ratio, and the effect would be applied at 250 beats per minute. If the
T
R
S
is set to 1/2, it would be a 1:2 ratio, which means
EMPO
ATIO
ELECTOR
the effect would be applied at 62.5 beats per minute.
34. LCD P
D
ARAMETER
ISPLAY
shows the effect name and parameter that is relative to the
effect. It also shows the detected BPM, when applicable.
35. M
R
B
EMORY
ECALL
ANKS
for memorizing effect settings during a performance. By
pressing and holding any one of the numbered buttons for 2 seconds,
you can memorize all of the effects settings that are currently in place,
including Channel, BPM, Tempo Ratio, Tempo Sync On/Off,
Parameter, and EFX On/Off. Once you have memorized settings into a
recall bank, it can be recalled by simply pressing the button momentarily.
36. EFX P
S
(38): This rotary control selects the
ROGRAM
ELECTOR
DSP effect which will be applied to the audio, when engaged.
37. EFX P
C
ARAMETER
ONTROL
you to alter the parameter associated with the DSP effect.
38. EFX D
/W
C
(40): This rotary control allows you to
RY
ET
ONTROL
alter how much of the audio signal is sent through the DSP effects
section. For less intense effects, turn the control towards 'Dry'. For more
intense effects, turn the control towards 'Wet'.
39. EFX O
/O
B
(41): By pressing this button, the DSP
N
FF
UTTON
effect that is selected is turned On or Off.
Downloaded from
www.Manualslib.com
R
EPLACING THE
1. Remove the black brushed aluminum plate which outlines the Channel
and X-Fader section. The screws can be found at each corner of this plate.
2. To remove a channel fader, simply remove the two screws on the top and
bottom of the fader. Disconnect the connector which plugs into the bottom
of the fader, and replace it with a new fader. Verify that the fader is facing
EFX A
HANNEL
SSIGN
the appropriate direction before screwing it back in.
3.To replace the X-Fader, first unscrew the two outermost screws from the
in time to the
B
AP
UTTON
X-Fader, and disconnect the connector which plugs into the bottom of the
D
ARAMETER
ISPLAY
fader. Remove the two innermost screws on the front of the fader, to
BPM/T
B
(33)
UTO
AP
UTTON
remove the steel limiting plate. Attach the limiting plate to the new replace-
D
ARAMETER
ISPLAY
ment X-Fader (model RG-45 or RG-45PRO). Then, replace the connector
which plugs into the bottom of the fader, and replace the fader in the
appropriate direction before screwing it back in.
U
R
SER
EPLACEABLE
User replaceable parts are listed below, and may be obtained by calling
your nearest Gemini office, listed on the back cover page of this manual.
B
(33).
UTTON
CROSSFADER: RG45 OR RG-45PRO
BPM/T
B
(33). When
CHANNEL FADER: 072-127
AP
UTTON
CHANNEL AND X-FADER KNOB: 002-742
PARAMETER CONTROL FADER KNOB: 002-741
S
to 2 would be a 2:1
ATIO
ELECTOR
GROUND TERMINAL: 146-710
SPECIFICATIONS
(36): This blue backlit display
Inputs:
Phono.....................................................................................3 mV, 47 KOhm
(37): These banks are useful
Line....................................................................................150 mV, 27 KOhm
MIC 1, MIC 2, MIC 3..........................................1.5 mV, 1 K Ohm Balanced
MIC 1 High.........................................................................................± 12dB
MIC 1 Mid..........................................................................................± 12dB
MIC 1 Low..........................................................................................± 12dB
Talkover Attenuation.............................................................................-16dB
Outputs:
(39): This slide control allows
Master/Zone/Booth RCA....................................................0 dB 1V, 400 Ohm
Max......................................................................................20V Peak-to-Peak
Record..................................................................................225 mV, 5 KOhm
Balanced Master...........................................................2V, 400 Ohm
General:
Frequency Response.................................................20Hz - 20KHz +/- 2 dB
Distortion.........................................................................................< 0.02%
S/N Ratio...........................................................................Better Than 80 dB
Headphone Impedance.....................................................................16 Ohm
Power Source..........................................................115/230V, 60/50Hz, 20W
manuals search engine
X-F
C
F
:
ADER AND
HANNEL
ADERS
P
:
ARTS
<7>
WEIGHTS AND DIMENSIONS:
Dimensions: 12.5 x 4.2 x 14" (318 x 107 x 356 mm)
Unit Weight: 12 lbs (5.44 kg)
Specifications and design are subject to change without notice for purpose
of improvement.
*The stated warranty does not affect statutory local warranties
OPTIONAL ACCESSORIES:
DJX-05 Professional Monitoring Headphones
DJX-05
GX-450 Powered ABS Loudspeakers
GX-450
For more information on new and exciting Gemini products, visit our
website at http://www.geminidj.com!
NOTES:
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
Werbung
Inhaltsverzeichnis
