Werbung
Quicklinks
Werbung
Verwandte Anleitungen für Ripmax Acro Wot Foam-E
Inhaltszusammenfassung für Ripmax Acro Wot Foam-E
- Seite 2 Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Chris Foss Chris Foss The Designer / Der Designer The fascination of flight captured Chris's imagination early on in his life when he started building, from kits and plans, simple free flight gliders and rubber powered models.
-
Seite 3: Introduction / Einführung
Introduction / Einführung Congratulations on your purchase of the ACRO WOT Foam-E! This is not just any foam model... it's a very clever ACRO WOT that can be flight ready in under 30 minutes! The beautiful EPO mouldings hide an innovative internal structure that adds strength where needed and locks all the components together. - Seite 4 Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Stage 1 / Schritt 1 Locate the tail assembly onto the fuselage, ensuring the control horn is on the underside. Richten Sie das Höhenleitwerk auf dem Rumpf aus, und achten Sie darauf, dass das Ruderhorn auf der Unterseite ist.
- Seite 5 Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Stage 6 / Schritt 6 Ensure that the elevator torque rod locates in the notch moulded in the rudder Vergewissern Sie sich, dass das Höhenrudergestänge in der vorgeformten Mulde im Ruder sitzt.
- Seite 6 Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Stage 11 / Schritt 11 Insert the screws through the horn, and re-attach the backplate to secure the horn. Take care not to over-tighten the screws. Schieben Sie die Schrauben durch das Horn, und besfestigen diese in der Sicherungsplatte auf der Rückseite, um das Horn zu sichern.
-
Seite 7: Radio Installation
Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Radio Installation ARTF The Acro Wot ARTF is supplied without transmitter or receiver. Connect the factory installed servos to your choice of receiver. Connect the electronic speed controller to the receiver's throttle channel. - Seite 8 Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Radio Installation The Acro Wot RTF is supplied with a factory installed S-FHSS receiver and high quality 2.4GHz transmitter. The transmitter and receiver are compatible with Futaba 2.4GHz S-FHSS radio systems such as the 6J, 8J and 18MZ.
- Seite 9 Acro Wot Foam-E Instructions / Acro Wot Foam-E Anleitung Stage 18 / Schritt 18 Locate the propeller and spinner assembly. Remove the two screws retaining the spinner nose to remove the propeller adaptor. Nehmen Sie den Propeller mit montiertem Spinner.
-
Seite 10: Control Throws
Installing your choice of Li-Po is simple. Twist the hatch retaining latch 90° and remove the hatch on the underside of the model. The ACRO WOT Foam-E uses the popular 'T' style connector. Once the Li-Po has been slid into its bay, it can be retained with a little foam packing or a strip of Velcro. - Seite 11 Subsequent flights should also be supervised, and assisted where necessary, by an experienced pilot. Always fly the ACRO WOT Foam-E in a safe location at a recognised club. For further information on flying in the UK, please contact: - British Model Flying Association (BMFA), Chacksfield House, 31 St Andrews Road, Leicester. LE2 8RE. Tel: +44 (0) 116 2440028 Fax: +44 (0) 116 2440645 or visit www.bmfa.org...
- Seite 12 Spare parts are available for the ACRO WOT Foam-E from all Ripmax stocked model shops. In case of any difficulty, any product queries, or to locate your local Ripmax stockist, please write to the address below or visit www.ripmax.com. Ersatzteile sind für den ACRO WOT Foam - E in allen Modellbaufachgeschäften, die Ripmax vertreiben, verfügbar. Sollten Sie Schwierigkeiten haben ein Produkt zu finden, wenden Sie sich bitte an Ihren Fachhändler, schreiben Sie an die unten aufgeführte Adresse, oder besuchen Sie unter www.ripmax.com.