Hama 00049278 Bedienungsanleitung Seite 9

Downloaded from www.Manualslib.com
Installing the SATA PCI Controller on Windows Vista/7
(32-bit and 64-bit versions):
After Windows has fi nished booting, a window appears
with the title "Found New Hardware". It offers you three
options. Select the fi rst option (Locate and install driver
software (recommended).
You are now asked by User Account Control whether you
want to continue the procedure. Click -> Continue.
After a short time, Windows displays a dialog box in which
you are asked to insert your driver CD-ROM. Follow the
request and then click -> Next. Wait until the
"Searching disc for software.." window is displayed.
Windows now displays a message confi rming that the
drivers were successfully installed. Click -> Close to
complete installation. Remove the driver CD-ROM from your
drive and keep it in a safe place so that the driver can be
reinstalled if required.
You can verify whether the controller has been successfully
installed by checking under Start (Windows logo) ->
Control Panel -> System and Maintenance -> Device
Manager. In some circumstances, you may be asked by the
User Account Control for confi rmation. Click -> Continue.
The following entry must appear without a yellow
exclamation mark.
• Storage controllers:
Silicon Image SiI 3512 SATARaid Controller
Installing the SATA PCI Controller on Windows XP and
Media Center Editions:
1. After booting, the Found New Hardware Wizard appears
and asks you if it should connect to Windows Update;
select "No, not this time". Click -> Next to continue.
2. In the next window, you are asked "What do you want
the wizard to do?". Select the option "Install from a list
or specifi c location (Advanced)". Then click -> Next to
continue.
3. Insert the enclosed driver CD-ROM into your drive.
4. Choose the option "Search removable media (fl oppy,
CD-ROM...)" and then click -> Next. The Hardware
Wizard searches the driver CD-ROM and then tells you
that the driver was installed successfully. Then click ->
Finish.
You can check whether the controller was installed
successfully under Start -> Control Panel -> Performance
and Maintenance -> System -> Hardware -> Device
Manager. The following entry should appear without a
yellow exclamation mark.
8
manuals search engine
• SCSI and RAID controllers
Silicon Image SiI 3512 SATARaid Controller
Installing the SATA PCI controller on Windows XP x64
Edition:
1. After booting, the Found New Hardware Wizard appears
and asks you if it should connect to Windows Update;
select "No, not this time". Click -> Next to continue.
2. In the next window, you are asked "What do you want
the wizard to do?". Select the option "Install from a list
or specifi c location (Advanced)". Then click -> Next to
continue.
3. Insert the enclosed driver CD-ROM into your drive.
4. Choose the option "Search removable media (fl oppy,
CD-ROM...)" and then click -> Next. The Hardware
Wizard searches the driver CD-ROM and then tells you
that the driver was installed successfully.
Note: Windows may inform you that the driver has not
passed Windows Logo testing, click "Continue installation"
to install the driver.
5. Then click -> Finish.
You can check whether the controller was installed suc-
cessfully under Start -> Control Panel -> Performance and
Maintenance -> System -> Hardware -> Device Manager.
The following entry should appear without a yellow
exclamation mark.
• SCSI and RAID controllers
Silicon Image SiI 3512 SATARaid Controller
Installing the SATA RAID controller on Windows 2000:
1. After booting, the Found New Hardware Wizard
appears; click -> Next to continue the procedure.
2. In the next window, you are asked "What do you want
the wizard to do?". Select "Search for a suitable driver
for my device (recommended)" and click -> Next.
3. Insert the enclosed driver CD-ROM into your drive.
Select only the "CD-ROM drives" option. Then click ->
Next.
You can verify whether the controller has been successfully
installed by checking under -> Start ->Settings -> Control
Panel -> System -> Hardware -> Device Manager. The
following entry should appear without a yellow exclamation
mark.