Technical Data; Attachment And Operation - Zgonc yellow Gardenline NEW GENERATION YGL N.G. 2700 Originalbetriebsanleitung

• Use a surge protector with a release current of
30 mA or less.
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
• Carefully follow the maintenance, control and
service instructions in this manual.
• Practise using the saw (sawing logs on a sawhorse)
and get an experienced user or a specialist to
explain to you the function of the saw, the way of
working, the techniques of sawing and the personal
protection equipment.

6. Technical data

Cutting data chainsaw
Cutting lenght cm
Bar lenght cm
Capacity oiltank l
Type of oil
Saw chain division
Drive link thickness mm
Saw chain type
Number of teeths drive
sprocket
Tooth pitch of drive sprocket
Chain brake
Guide bar type
Engine
Motor V / Hz
Power W
Cutting speed max. m/s
Weight kg
Weight without bar and chain
kg
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
Sound pressure L = 93,5 dB(A)
pA
Sound power L = 104,4 dB(A)
WA
Guaranteed Sound power LWA = 107 dB(A)
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A (front handle) = 2,5 m/s
hv
Vibration A (rear handle) = 5,7 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
30 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
44
45,5
0,15
wear resistant oil
3/8"
1.27
3/8,050x62DL
7 x 9,525
3/8"
yes
AP18-62-507P
230-240 V / 50 Hz
2700
15
5,6
4,8
2
2
• The specified vibration emission value has been
measured according to a standardised testing
procedure and can be used for comparison of one
electric tool with another;
• The specified vibration emission value can also be
used for an initial assessment of the load.
Warning:
• The vibration emission value can vary from the
specified value during the actual use of the electric
tool, depending on the type and the manner in
which the electric tool is used;
• Try to minimise stress from vibrations as low as
possible. Some examples of means for reducing
the vibration stress are wearing gloves while using
the tool and limiting work time. In the process all
parts of the operating cycle must be taken into
account (such as times in which the electric tool is
switched off or time in which it is switched on, but is
not running under a load).

7. Attachment and operation

Warning!
Always wear safety
protective gloves and heavy-duty work clothes!
Use the saw only with approved extension cables with
the prescribed insulation and connections designed
for outdoor use (approved rubber-sheathed cables)
which fit the chainsaw plug.
The chain saw is equipped with safety switches,
requiring the use of both hand. The chainsaw works
only when one hand is pushing the button 11 and 13
at the same time. If the chainsaw does not run, the
chain brake must be released at the front finger guard
(3). Be sure to read the sections "Chain brake" and
"Releasing the chain brake " on this point.
Assembly
Fitting the guide bar and chain (Fig. 1, 2, 3)
Warning! If the chain saw is already connected to
the power supply: Pull the plug from the socket outlet.
Wear protective gloves whenever doing any work on
the saw chain.
Important: The front finger guard (3) must always be
in the top (vertical) position (Fig. 5).
The guide bar and saw chain are supplied separately.
To assemble, first unscrew the lock nut (SDS-
system/5) and remove the guide bar cover (6). The
guide bolt (17) must be in the centre of the guide.
If necessary, adjust the chain tensioning with the
chain wheel (Fig. 3, 5a).
Warning! To prevent injury on the sharp cutting
edges, always wear gloves when assembling,
tensioning and checking the chain.
Before assembling the guide bar with the saw chain,
check the cutting direction of the teeth!
goggles, ear muffs,