Safety Notes - Monacor HDTVI-100 CON Anleitung

HDTVI-100 CON
Order number 18.7990
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
HD TVI Video Signal Converter
These instructions are intended for install-
ers of video surveillance systems. Please
read the instructions carefully prior to
operation and keep them for later refer-
ence.
1 Applications
This converter is used to convert a TVI video
signal (e. g. from a camera) into an HDMI™,
VGA or composite (CVBS) video signal, e. g. for
display on a monitor or TV set. As an alterna-
tive, the CVBS output jack (d) can be used as a
TVI feed-through output or as a second input
for another TVI signal. When two input signals
are used, the picture-in-picture display feature
is available.

2 Safety Notes

The units (converter and power supply unit)
correspond to all relevant directives of the EU
and are therefore marked with
WARNING The power supply unit uses
dangerous mains voltage. Leave
servicing to skilled personnel
only. Inexpert handling may
result in electric shock.
Operating Modes and Their Setting Options
Number of inputs
2
(d) = TVI feed-through output
1
1 2 3 4
ON
1 2 3 4
2
ON
* Note: The resolution selected will also determine the video system for the CVBS output.
For PAL, select a resolution with a frame rate of 50 Hz (display "...@50"); for NTSC, select a resolution of 60 Hz (display "...@60").
VGA OUT
a b
ELECTRONICS FOR SPECIALISTS
•
The units are suitable for indoor use only.
Protect them against dripping water, splash
water and high air humidity. The admissible
ambient temperature range is 0 – 40 °C.
•
Do not operate the converter and immedi-
ately disconnect the power supply unit from
the mains socket
1. if one of the units is visibly damaged,
2. if a defect might have occurred after a unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case, the units must be repaired by
skilled personnel.
•
For cleaning only use a dry, soft cloth; never
use water or chemicals.
•
No guarantee claims for the units and no
liability for any resulting personal damage or
material damage will be accepted if the units
are used for other purposes than originally
intended, if they are not correctly connected,
.
or if they are not repaired in an expert way.
If the units are to be put out of oper-
ation definitively, take them to a local
recycling plant for a disposal which is
not harmful to the environment.
Output signals
1 2 3
(loopout)
ON
2
(d) = CVBS
1 2 3
ON
One input signal
1 2 3
ON
Two input signals
(picture in picture) 1 2 3
ON
CVBS/HD-TVI HD-TVI
2 1
IN/OUT IN
L
S
C
c d e
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
Resolution for HDMI and VGA*
480p/60  576p/50  720p/60  720p/50
4
 1080i /60  1080i /50  1080p/60  1080p/50
Reduction of image width ("underscan")
4 for the CVBS signal (20 % max.)
Selection of the input signal (display "*...")
4
Position of the image inserted
Input signal swapping
4
Size of the image inserted
b f
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
3 Installation and Operation
The mounting brackets (b) can be used to in-
stall the converter, e. g. on a wall.
1) Set the operating mode (
to connecting other units by means of the
switches (h).
2) Use a 75 Ω cable to connect the video
source (e. g. camera) to the BNC jack HD-
TVI 1 IN (e). If the BNC jack 2 IN /OUT (d)
has been configured as an input by means
of switch 2 (h), connect the second video
source to this jack.
3) Proceed as required:
– Connect the HDMI input of a monitor or
TV set to the output HDMI OUT (j).
– Connect the VGA input of a computer
monitor to the output VGA OUT (a).
– Connect the video input for CVBS signals
of a surveillance monitor or video recorder
to the jack CVBS / HD-TVI 2 IN /OUT (d) or
use the jack as a feed-through output for
the TVI input signal.
Note: The outputs can be used at the same time.
4) Connect the plug-in power supply provided
to the low-voltage jack DC 12 V (f) and to a
mains socket (230 V/50 Hz). The converter is
switched on.
Button functions

Lower resolution
−2 % (image wider) +2 % (image smaller)
1
IN (e)
1 2 3 4
ON
1 2 3 4
ON
DC 12 V
P SETTING
S
1 2 3 4
H
ON
g h
ELECTRONICS
☞
table) prior
 + 

Higher resolution —
—
2
—
IN (d)
—
HDMI OUT
i j
A-1746.99.02.10.2016