Renkforce 1170562 Bedienungsanleitung Seite 2

G Operating Instructions
microSD card collector
Item no. 1170562
Intended use
The product has two slots for microSD / microSDHC memory cards. Through the in-
tegrated controller, the two memory cards are combined into a single data storage
medium. Depending on the memory cards used, the speed when reading / writing to
the disk can become higher.
The connection is like that of a conventional USB stick to a USB port on the computer,
thus eliminating the need for a driver software.
This product complies with the applicable National and European regulations. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• Card collector
• Operating Instructions
Safety Instructions
T he warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any con-
sequential damage!
N or do we assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! In such
cases, the warranty will be null and void.
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Do not open/disassemble
it!
• The product is not a toy and should be kept out of the reach of children.
• The product must not get damp or wet.
• Do not leave packaging material carelessly lying around since it could
become a dangerous plaything for children.
Inserting/removing memory cards
Insert one microSD / microSDHC memory card (microSD up to max. 2 GB, microSDHC
up to 32 GB) into one of the memory card slots.
When different memory cards are used, then the achievable speed when
reading or writing is less than that with two identical memory cards.
The memory cards are grouped in a single drive. Therefore: If one of the mem-
ory card is removed (or the memory cards are swapped in both drawers ),
all data may be lost from both memory cards!
If you want to remove the memory card (e.g. exchange for two other memory
cards), mark them accordingly!
Connection and getting started
Connect the card collector to a free USB2.0 port on your computer. During the initial
connection, Windows recognises the new hardware; the drivers are already included
in Windows.
When you first connect the card collector (with memory card microSD / microSDHC
inside), it will appear as a new drive e.g. in the file manager of Windows (the 2 memory
cards are managed as a single correlated drive, so 2 drives do not appear in the file
manager, but only one).
However, before data can be stored on it, the drive must be formatted (as with a new
hard disk). If you click on the drive in Windows, a message appears that the drive is
not formatted and asks if you would like to format it. Accept this.
Any file system can be chosen (e.g. NTFS). Should exFAT be used, a system update
for Windows XP should be done, because exFAT is not supported by Windows XP
otherwise. Visit the website www.microsoft.com and search there for the update of
the exFAT file system for Windows XP.
Deleting or creating partitions is same as in Windows from the control panel or in disk
management. This is required even if the memory cards used in the card collector will
be reused later!
After formatting the new drive, it can be used e.g. as a conventional USB stick.
Disconnecting the card collector
If a read/write access is underway in the card collector (LED flashes), wait until it is
finished. Afterwards, disconnect the card collector from the USB port.
If the card collector is removed during a read/write access, data on the me-
mory card may be damaged and the memory card may have to be formatted
once again.
Disposal
Dispose of the unserviceable product according to the relevant statutory
regulations!
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.