Hacker SKALAR Bedienungsanleitung Seite 2

Hacker Motor GmbH
Schinderstraßl 32
Tel.: 0049 (0) 871-953628-0
Fax.:0049 (0) 871-953628-29
info@hacker-motor.com
D-84030 Ergolding
Manual for SKALAR SC Brushless Motor
Welcome to the team!
With this hacker SCALAR motor you purchased a product that is designed not
just for the competition, but also for all recreational riders who expect maxi-
mum performance and reliability of their brushless motor.
Features:
•
Weight optimized design
•
Optimum of cooling
•
U-shaped solder contacts
•
High quality ball bearings
•
Easy maintenance design
•
17mm standard-rotor
PRECAUTIONS & WARNINGS
Read these instructions carefully before using your new motor!
Avoid using a wrong gear ratio by continuously monitoring the motor and
controller temperature.
Make sure that the motor temperature does not exceed 80 ° C and the
controller temperature does not exceed 90 °C.
When mounting the motor, pay attention to the correct length of screws and
not to over tight them with to excessive torque force.
ASSEMBLY
During assembly, make sure that you use high quality screws. Screws made of
brass, or aluminium is not suitable for this case!
The screws should not protrude more than 5mm in the motor housing as this
could damage the motor winding her.
Damage caused by excessively long screws will be not covered by the
warranty.
The SCALAR has 3 U-shaped solder contacts, which are labelled A, B and C.
Solder your controller - according to controller instructions - to the motor.
During the soldering process, ensure that the connections are not shorted by
solder to each other.
CLEANING & MAINTENANCE
Clean your SCALAR motor regularly in the area of ball bearings with a brush
and oils to the ball bearings with a suitable ball bearing oil.
Avoid the use of brake cleaner or other cleaning spray.
GEAR RATIO
Gear ratio will depend on many factors, so that we can give only recommenda-
tions at this point.
Basically, you should consider the instructions of your car.
An important criterion to determine whether your engine is working properly,
make sure that the temperature should never exceed 80 ° C. Take care and
start with a conservative gear ratio.
TECHNICAL INFORMATION
Diamensions
Weight 196g
Length 53mm
Shaft length 18mm
Shaft diameter 5mm
Diameter 36mm
Magnet diameter 17mm
Magnet material Neodym-Eisen-Bor ( NdFeB )
Sensored / sensorless yes
adjustable Timing No
Order.-Nr. Voltage kV Power
4.5T 71004500 3,2V - 7,4V 5000 796W
5.5T 71005500 3,2V - 7,4V 4200 746W
6.5T 71006500 3,2V - 7,4V 3800 697W
GERNERAL WARRANTY PROVISIONS
Hacker Motor GmbH products will be manufactured in accordance with the
highest quality criteria.
We provide the legal guarantee, to be free of defects on material and work-
manship.
There will be no liability for typical use sign of wear.
The warranty does not cover defects which are a result of misuse, improper
maintenance, or mechanical damage.
This is among other things on:
•
Outside mechanical damage.
•
Overload.
•
Damages on the motor due to high pollution.
•
rust
•
use of aggressive cleaning agent
REGULATIONS FOR REPAIR
Before returning your product for repair, please check all other components in
order to avoid any operator error..
By returning of the product, the customer, should identify whether the product
will be repaired in any case or not. In the case that no warranty or guarantee
applies, the product testing and possible repair or service will be charged
according to our price list. A guarantee or warranty can only be accepted if a
copy of your receipt is attached. On request, we will offer you a repair quote.
On our repair quote, we are bound for two weeks from the date of issue. By
carrying out the repair the cost for the repair quote will not be charged. For
quick repair and return service, please provide a detailed description of
the failure and full address details.
DECLARATION OF CONFORMITY
For the products manufactured by Hacker Motor GmbH mentioned in this
manual the compelling and relevant EC Directive will apply:
EMV-Directive: 2004/108/EG
The following special directives will apply:
EN 55014-1:2006 + A1:2009
EN 55014-2:1997 + Corrigendum: 1997 + A1:2001 + A2: 2008
Ergolding, 04.02.2012
Efficiency
90%
88%
88%
Information for Users on disposal of electrical equipment
and electronic equipment (private households)
According to the basic business principles, your product is
made from high quality materials, which are recyclable and
reusable.
This symbol on the products and / or accompanying documents means that
used electrical and electronic products must be at the end of their lifetime
separated from household waste.
Please take these products for the treatment, recovery and recycling to
designated collection points, which will receive the devices free of charge.
The Proper disposal of this product, prevent any potential adverse effects on
humans and the environment which could otherwise arise from inappropriate
waste handling at the end of its lifetime. For more precise details of your
nearest designated collection point, contact your local authority.
For business users in the European Union
Please contact your dealer or supplier for further information if you wish to
dispose electrical and electronic equipment. He holds further information ready
for you.
Information on Disposal in other Countries outside the European Union.
This symbol is only valid in the European Union.
Hacker Motor GmbH
Schinderstraßl 32
D-84030 Ergolding
Tel: +49 871-953628-0
Fax: +49 871-953628-29
E-Mail: info@hacker-motor.com
Irrtum und Änderungen vorbehalten
WEEE-Reg.-Nr. DE 55352581
Copyright 2012 Hacker Motor GmbH. All rights reserved.