Forgast FG00408 Benutzerhandbuch Seite 15

2. ABOUT THE EQUIPMENT
2.1 HOW DOES IT WORK?
The cationic resins in the softener's tank transform calcium carbonate in
sodium carbonate, which is water-soluble at the working temperatures of both
coffee makers and ice makers machines.
The transfer of sodium ions between the resins and water is imperative to
soften drinking water, but this process tends to decline in proportion to the
flow rate and the consumption of water. For this reason, it is necessary to
regenerate the exhausted resins by making water and salt flow through them,
therefore returning them to their active state.
The resins gradually lose their cationic function, and consequently their
efficiency, with each regeneration. We recommend replacing them after seven
years of use.
2.2 EQUIPMENT DESCRIPTION (fig. 1)
The main components of the water softener are:
1 tank containing the resins for water softening
2 three-way taps (fig. 1, C-D)
1 tank lid (fig. 1, G)
2.3 THE PACKAGING CONTAINS
1 complete water softener
1 instruction manual
2 drain pipes (fig. 1, E-F)
2.4 TECHNICAL FEATURES
Pressure of feed water
Nominal flow rate at 4 bar
Room temperature
Joints for the connection to the water system: 3/8"G; 3/4"G (fig. 3)
2.5 CHARACTERISTICS OF FEED WATER
Feed water must be:
Drinkable and clean (SDI 1)
Temperature must be between 6° and 25°C
Hardness must be below 900 ppm CaCO
2.6 EQUIPMENT PERFORMANCE BASED ON WATER HARDNESS
h WEIGHT
MODEL
[mm] [kg]
5 l 300 5
8 l 400 7,5
12 l 500 9,5
16 l 600 12
20 l 900 19
0,1 ÷ 0,8 MPa (1 ÷ 8 bar)
1000 l/h
4°C - 35°C
(90°f)
3
RESIN SALT/RIG.
20°f
[l] [kg]
11°d
200 ppm CaCO
3,5 0,5 1050
5,6 1 1680
8,4 1,5 2520
11,2 2 3360
14 2,5 4200
3. INSTALLATION
3.1 PACKAGING
Before the installation, check that the equipment was not damaged by the
transport and does not show any anomaly. If in doubt, ask your seller, whose
information is written on the back of this manual.
Don't throw the package away for some time, being careful to keep any
dangerous or small parts of the package away from children.
3.2 CHOOSING THE PLACE OF INSTALLATION
Ensure that any other water treatment machine is not present upline of the
place of installation.
Ensure that feed water comes from a drinking water pipe. We recommend
checking the chemical and physical parameters of the drinking water as well as
its hardness before installation.
Install the equipment near a floor sink, to dispose of the waste water produced
by the regeneration.
Install the equipment in a dry place that can be easily accessible to maintain,
regenerate and clean the equipment. Do not install the equipment in dirty and
unhygienic places, or in any place difficult to clean.
Ensure that room temperature in the place of installation is between 4°C and
35°C.
Keep away from corrosive or acid products.
Do not install in places where electric safety norms or personal safety norms
are openly disregarded.
Hydric pressure must not be under 0.1 Mpa (1 bar) or over 0.8 Mpa (8 bar).
(We recommend at least 3 or 4 bar)
If hydric pressure is over 8 bar, it is necessary to install a pressure adaptor.
Salt packages or boxes must not be kept in humid places or in direct contact
with the floor: keep it, for example, on a wooden pallet.
LITRES OF WATER SOFTENED, BASED ON HARDNESS
30°f 40°f
16°d 22°d
300 ppm CaCO 400 ppm CaCO
3 3
700 525
1120 840
1680 1260
2240 1680
2800 2100
15
50°f 60°f
28°d 33°d
500 ppm CaCO 600 ppm CaCO
3 3
420 350
672 560
1008 840
1344 1120
1680 1400
3