Safety Notes; Operation - Monacor PSS-510DC Bedienungsanleitung

PSS-510DC PSS-1230DC
PSS-608DC PSS-1250DC
PSS-906DC PSS-2405DC
PSS-1205DC PSS-2415DC
PSS-1210DC PSS-2430DC
ELECTRONICS FOR SPECIALISTS
Switch Mode Power Supply Unit
These instructions are intended for users with-
out any specific technical knowledge. Please
read these instructions carefully prior to oper-
ation and keep them for later reference.
1 Applications
This power supply unit is used for direct current
supply of small units. Depending on the unit, the
output voltage is 5 V , 6 V , 9 V , 12 V or 24 V . The unit
is protected against short circuit, overload and over-
heating. The special feature of the power supply
unit is its extra low current consumption when the
unit connected has been switched off: < 0.3 W or,
for models PSS-1250DC and PSS-2430DC, < 0.5 W.

2 Safety Notes

This unit corresponds to all relevant directives of
the EU and is therefore marked with
WARNING The unit uses dangerous mains volt-
age. Leave servicing to skilled per-
sonnel only. Inexpert handling may
result in electric shock.
•
The unit is suitable for indoor use only. Protect
it against dripping water and splash water, high
air humidity and heat (admissible ambient tem-
perature range 0 – 40 °C).
•
Do not operate the unit and immediately discon-
nect it from the socket
1. if the unit is visibly damaged,
2. if a defect might have occurred after the unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled
personnel.
•
For cleaning only use a dry, soft cloth; never use
chemicals or water.
Specifications
Power supply
Power consumption in no-load operation < 0.3 W < 0.3 W < 0.3 W < 0.3 W < 0.3 W < 0.3 W < 0.5 W < 0.3 W < 0.3 W < 0.5 W
Output voltage
Max. output current
Length of connection cable
Low-voltage plug
Weight
ELECTRONICS FOR SPECIALISTS
.
⎓ 5 V ⎓ 6 V ⎓ 9 V
1 A 800 mA 660 mA 500 mA
65 g 65 g 65 g
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
•
No guarantee claims for the unit and no liability
for any resulting personal damage or material
damage will be accepted if the unit is used for
other purposes than originally intended, if it is
not correctly connected, if it is overloaded, or if
it is not repaired in an expert way.
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harmful
to the environment.

3 Operation

Before connecting the power supply unit, always
observe the following:
1. The output voltage of the power supply unit
must comply with the operating voltage of the
unit to be supplied with power (
the power supply jack of the unit).
2. The current consumption of the unit to be sup-
plied with power must be lower than the max-
imum output current of the power supply unit
( specifications of both units).
☞
3. The power supply jack of the unit to be con-
nected must have the positive pole at the cen-
tre contact. The positive pole is indicated by the
symbol or a similar symbol at the jack.
4. The plug of the power supply unit (outside
diameter 5.5 mm, inside diameter 2.1 mm) must
fit correctly.
Connect the power supply unit to the unit to
be supplied with power and then to a socket
(100 – 240 V, 50 – 60 Hz). The red LED power indi-
cator of the power supply unit will light up.
Subject to technical modifications.
100 – 240 V, 50 – 60 Hz
⎓ 12 V ⎓ 12 V ⎓ 12 V ⎓ 12 V ⎓ 24 V ⎓ 24 V ⎓ 24 V
1 A 3A
1,8 m
5.5 mm / 2.1 mm (outside / inside diameter)
65 g 135 g 280 g
marking of
☞
5 A 500 mA 1,5 A
340 g 135 g 280 g
A-1095.99.03.02.2018
3 A
340 g