Sehr geehrter Kunde! Mit der Wahl für ein videotronic Produkt haben Sie sich für ein professionelles Gerät entschieden, das höchste Qualität und Zuverlässigkeit gewährleistet. Für das entge- gengebrachte Vertrauen möchten wir uns an dieser Stelle nochmals bedanken und Sie bitten, die nachfolgenden Hinweise vor Inbetriebnahme genau durchzulesen, damit Sie in den vollen Genuß...
Allgemeine Informationen Funktionsbeschreibung Das neue videotronic infosystems Wetterschutzgehäuse überzeugt durch elegantes, fortschrittliches Design und ein hervorragendes Preis-Leistungsverhältnis. Die Gehäuse sind für alle videotronic infosystems CCD-Kameras mit Fest-Objektiven bzw. Vario-Objektiven ausgelegt. Der elektrisch isolierte Aufbau der Kamera verhindert jegliche Art von Kriechströmen durch Masse-Potentialausgleich und die damit verbundenen Brummschleifen im Video- bild.
Sicherheitshinweise Lesen Sie diese Gebrauchsanweisung aufmerksam durch, bevor Sie die Kompo- nenten in Betrieb nehmen. Damit werden eventuelle Schäden sowie Funktionsstö- rungen durch nicht sachgerechten Gebrauch vermieden. Die Installation darf nur durch Kundendienst oder Fachwerkstatt nach den beste- henden VDE-Richtlinien ausgeführt werden. Betreiben Sie das Gerät ausschließlich an der angegebenen Betriebsspannung.
Montage und Anschluß MONTAGE DER WANDHALTERUNG a) Positionieren Sie die Halterung (1) und stecken Sie die Abdeckung (2), die Gehäusehalterung (3) und die Halterung (4) in das obere Loch b) Schrauben Sie die Schraube (5) von un- ten in die Halterung (4), ohne sie fest anzuziehen.
N L1 connec- tion PE - Kamerabühne I T 1 Heizung G P 1 G P 2 PE - Gehäuse S T - 3 4 1 - 1 e r m e s Lösen Sie bitte die mit dem Pfeil markierte Schraube.
Anhang Hinweise im Störungsfall Fehlerbeschreibung Ursache Kamerastation liefert kein Überprüfen Sie den Anschluß der Betriebs- Videosignal. spannung (230 V AC oder 12 V DC) an der An- schlußplatine. Überprüfen Sie den Anschluß des Videokabels an der Anschlußplatine. Überprüfen Sie die Funktion Ihres Netzteiles (12 V DC) Überprüfen Sie die Anschlüsse an der Kamera (Video / Spannung).
Seite 10
Dear Customer! By selecting this videotronic product you have decided to use a professional device which guarantees highest quality and reliability. We like to thank you very much for your confidence and kindly ask you to read the following instructions carefully before operat- ing in order to take full advantage of all quality features of this product.
General Information Function Description videotronic infosystems‘ new weatherproof camera housing convince with their elegant, progressive design and give excellent value for money. The housings are suitable for all videotronic infosystems CCD cameras with fixed or vari-focal lenses. The construction of the mounting base is electrically insulated and avoids any type of leak current by ground potential and the resulting hum in the video picture.
Safety Precautions Read these instructions carefully before operating the components in order to avoid malfunctions and damages caused by improper installation or use. Installation may only be carried out by authorised personnel according to the local safety regulations. Only operate the device with the stated operating voltage. Never use the device for other purposes than designated.
Mounting and Connecting Connection Examples INSTRUCTIONS FOR THE ASSEMBLY OF THE BRACKET Position the bracket (1) as indicated on the drawing and insert the cover (2) into the upper hole, the joint (3) and the spherical pin (4) Screw the screw (5) to the bottom of the spherical pin (4), without tightening the screw.
N L1 connec- tion PE - camera I T 1 Heater G P 1 G P 2 PE - housing S T - 3 4 1 - 1 e r m e s In order to fit the camera on the slide, Please loosen the screw shown with an arrow and swivel the slide.
EXHIBIT Exhibit Troubleshooting Error Description Cause camera station gives no video check the power supply connection (230 signal V AC or 12 V DC) to the connection cir- cuit board check the connection of the video cable to the connection circuit board check the function of your power supply (12 V DC) check the connections to the camera...
RAL 7035 grey/beige powder-coated; front / rear: dark grey Vicon Deutschland Tel.: 04321-879-0 Fax: 04321-879-97 Kornstieg 3 D-24537 Neumünster/Germany Irrtümer sowie Änderungen, die dem technischen Fortschritt dienen, vorbehalten. Technical specifications are subject to change without prior notice. 2009 Vicon Deutschland GmbH...