Jumbo ayce LPL-15A-4 Gebrauchsanweisung Seite 36

Under the P-function, you can also set the weekly timer. Pressing WEEK, allows you to
●
set or check the weekly timer. Please note! To set the weekly timer, you must first
enter the day and time correctly.
Setting weekly timer
Press the WEEK button and hold it in. A blinking '01' will now appear on the display.
●
Use the + and – buttons to choose "01" (one-off setting) or "][" (the setting your install
will be implemented every week). Confirm with SET.
Note: the setting(s) that you enter under 'one-off' (01) must fall into the current week.
On Sunday (day 7) at 24.00, all one-off settings will be turned to non- active. A setting
that you enter on Tuesday for Saturday will work, but a setting that you enter on
Saturday for Tuesday will not.
Note: a one-off setting (01) will only be implemented by the heater once, but the timer
setting will stay as non-active in the memory and therefore takes the place of one of
the four possible settings on that day. You are better off deleting it, see later.
ON now blinks. Use the + and – buttons to choose between ON and OFF: with or
●
without 'anticipation'. With ON, the heater will check the temperature in the room 20
minutes before it set activation time. If it needs to be heated by over 6 degrees, the
heater will switch on at full capacity in order to heat the room to the right temperature
by the activation time. For 3, 4 or 5 degrees' difference, it will switch on in the medium
setting and for 1 or 2 degrees, it will switch on at low capacity. If you would prefer not
to have this function, switch 'anticipation' to: OFF. Press set to confirm.
Please Note: The choice of 'one-off' or 'repeated' and 'yes or no' for 'anticipation' now
applies to all timer settings!
"01 SET ON" appears on the screen to signify that you can set the first 'on' time. You
●
can now use the + and – buttons to select the day of the week for the setting. Press SET
for the right day.
The temperature (standard 25°) now appears on the display and blinks. Use the + and –
●
buttons to adjust it, from 0 to 37°C. Confirm with SET.
The hour will now blink. Choose the right hour and confirm with SET.
●
The minutes will now blink. Choose the right minutes and confirm with SET. The first
●
activation time is now set.
Now, "01 SET OFF" will appear on the display, to indicate that you must set the
●
deactivation time. Do this in the same way as set out in the above 2 points. Your first
setting is now entered.
A '02' will now appear on the display. You can now set a second activation/deactivation
●
time; a total of 4 per day and 28 per week. If you don't need to, wait until the screen
returns to the standard settings.
Now switch the heater on using the ON/OFF switch. The screen will show P and OFF to
●
indicate that a setting has been programmed but that the heater is currently off. At the
set time, it will switch on and off automatically.
The set timer details will be retained after it is switched off using the main switch or
●
plug.
If you press repeatedly on WEEK, you will see the following timer settings, one after
●
the other:
-One-off or repeated
-Anticipation on or off
-Thermostat setting
-Timer on-time
-Timer off-time
-Next timer setting
If you would like to delete a specific setting, press and hold WEEK and then search for
●
the timer setting that you need. Go past 01- ][ and on/off first by pressing SET briefly.
When the number of the timer setting that you wish to change appears, press SET for a
little longer. You will hear a short beep and the selected setting has been deleted.
If you wish to delete all timer settings, press the WEEK button and hold. Press and hold
●
the MOD and SET buttons at the same time, until you hear a beep. The screen will
show 88:88, indicating that all settings have been deleted.
Please Note: all timer settings can only be deleted with the buttons on the operating
panel, not with the remote control!
If you wish to retain the timer details but do not want to use the timer for a while, push
●
and hold the WEEK button and then push and hold the MOD until TIME disappears
from the screen to indicate that the data will be retained but will not be active. By
pressing MOD again until TIME appears, you will reactivate the timer.
●
Screen protection:
If the settings on a working heater are not adjusted for 2 minutes, the LED display will go
out but ON will stay on. It will light up again when you press a button. If the heather is
switched off using the ON/OFF button, the OFF screen will stay on.
70 | 71
GB