Herunterladen Inhalt Inhalt Diese Seite drucken

Safety Information - EINHELL PROFI Silver Line PS-AS 14,4/1H Bedienungsanleitung

Elektronik-akku-bohrschrauber mit drehmomenteinstellung
Vorschau ausblenden Andere Handbücher für PROFI Silver Line PS-AS 14,4/1H:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Anleitung PS-AS 14,4_SPK1
GB
1. Layout:
1: Torque selector
2: Drill chuck
3: Clockwise/Counter-clockwise changeover
switch
4: ON/OFF switch
5: Battery pack
6: Battery charger
7: Pushlock button

2. Safety information

Please refer to the booklet included in delivery for the
safety instructions.
3. Important information
Be sure to read the following information before you
use your cordless screwdriver for the first time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 1 hour.
2. Only ever use sharp drill bits and screwdriver bits
which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables and
gas and water pipes when drilling and screwing
in walls.
4. Starting up:
Charging the NC battery pack
1. Take the rechargeable battery pack out of the
handle (Fig. 2), pressing the pushlock button at
the side to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the battery charger in the socket.
3. Insert the rechargeable battery pack into the
battery charger (Figure 3). The red LED will
come on to indicate that the battery pack is being
charged. The green LED will come on to indicate
that charging has been completed. Discharged
battery packs require approx. 1 hour for
charging. The temperature of the battery pack
may rise slightly during the charging operation.
This is normal.
8
20.08.2005
9:13 Uhr
Seite 8
If the battery pack fails to charge, check the
following:
- Whether there is voltage at the socket-outlet
- Whether there is proper contact with the charging
contacts in the battery charger.
If the battery pack still fails to charge, send
the battery charger
and the battery pack
to our customer services department.
To ensure that the NC battery pack provides long
service, you should take care to recharge it promptly.
At the latest you will certainly have to do this when
you notice the performance of your cordless
screwdriver falling away. Never fully discharge the
battery pack. This will cause it to develop a defect.
Torque selector (1)
The cordless screwdriver is fitted with a 17-setting
mechanical torque selector. The torque for each
screw size is set with the setting ring (1). The torque
is dependent on a number of factors:
On the type and hardness of the material
involved
On the type and length of the screw used
On the requirements that the screw connection
has to satisfy.
The grating disengagement of the coupling indicates
that the selected torque level has been reached.
Important! Only ever adjust the setting ring when
the device is at a standstill.
Drill
For drilling adjust the setting ring for the torque to the
last setting "Drill". In this drill setting the slip coupling
is non-functional. The maximum torque is available
for drilling.
Changeover switch (3)
The slide switch above the ON/OFF switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rotation
only when the drill is at a standstill. If you fail to
observe this point, the gearing may become
damaged. When the slide switch is in the middle
position, the ON/OFF switch is blocked.

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

44.710.31

Inhaltsverzeichnis