Technical Data; Assembly And Operation; Before Using For The First Time - EINHELL NEW GENERATION TPR 180 UG Bedienungsanleitung

Anleitung TPR 180 UG_SPK1
Always pull out the power plug before changing
the cutting wheel.
Use only suitable diamond cutting wheels.
Never leave the machine unattended in rooms
with children.
Always pull out the power plug before examining
the electric motor compartment system.

5. Technical data

Motor rating
Motor speed
A.c. motor
Insulation material class
Insulation
Cut length
Jolly length
Cut height 90°
Cut height 45°
Cutting table:
Dimensions
Diamond cutting wheel
Noise emission levels
The noise emitted by this saw is measured in
accordance with EN ISO 3744; EN ISO 11201
The noise at the workplace may exceed 85 db
(A). The user will require noise protection
measures if this is the case. (Wear ear-muffs!)
With-load
operation
Sound pressure level 94 dB(A)
Sound power level 107 dB(A)

6. Before using for the first time

The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench, the base frame supplied in delivery, or
similar.
All covers and safety devices must be correctly
attached before the machine is used for the first
time.
The cutting wheel must rotate smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
14.06.2006 9:01 Uhr Seite 9

7. Assembly and operation

7.1 Assembling the base frame (Fig. 3-8)
Fasten the 4 feet (14) to the base frame (15) as
shown in Figure 5/6. Then fit the two trough mounts
(e) as shown in Figure 7. Insert the trough (2) in the
base frame and fix it in place by tightening the star
grip screws (c).
7.2 Assembling the cooling water pump (Fig.
600 W S1
9/10)
3000 rpm
Place the cooling water pump (16) in the trough
230 V ~ 50 Hz
(2).
Fill with water until the pump (16) is full.
Class B
Place the complete tile cutting machine in the
IP54
trough (2) (see Fig. 9).
430 mm
Unscrew the star grip screw (10) (for securing
430 mm
during transportation!).
max. 25 mm
7.3 RCD plug (Fig. 17)
max. 17 mm
Connect the RCD plug (17) to the power supply.
Press the reset button (18) and the control lamp
500 x 385 mm
(19) will begin to shine. Press the test button (20)
to check the function of the RCD plug. If
ø 180 x ø 25.4
everything is working properly the control lamp
(19) will go out and the contact to the power
supply will be interrupted. The RCD plug triggers
at a fault current of 30 mA. Defective RCD plugs
must be replaced by a qualified electrician.
Press the reset key (18) again in order to be able
to start up the machine.
7.4 ON/OFF switch (Fig. 2)
To switch on, press the "1" on the ON/OFF
switch (12).
No-Load
Before you begin cutting, wait until the cutting
operation
wheel has reached maximum speed and the
70 dB(A)
cooling water pump (16) has started supplying
83 dB(A)
the cutting wheel with water.
To switch off, press the "0" on the switch (12).
7.5 Making 90° cuts (Fig. 9/12)
Loosen the star grip screw (21).
Set the angle stop (4) to 90° and retighten the
star grip screw (21).
Retighten the screws (22) to fasten the angle
stop (4).
Move the machine head (23) to the far end with
the handle (8).
Position the tile against the rail fence (5) or on
the angle stop (4).
Switch on the tile cutting machine.
Please note: Always wait until the cooling water
GB
9