Hella marine Naviled PRO Montage

Warranty Statement
Congratulations! The product you have selected comes from HELLA – one of the world's
leading manufacturers of lighting products. The product comes with a 5 year warranty from
end user purchase covering faults in materials, components or workmanship.
In the unlikely event that you should experience a confirmed warranty related problem with your
purchase, HELLA will, at its discretion, either repair, replace or refund the purchase price of the
product.
Warranty services may be obtained by returning the product within the warranty period to the
HELLA dealer where the product was originally purchased.
This warranty is in addition to and does not preclude any other rights or remedies available to the
consumer under any local legislation related to the provision of goods or services.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty does not cover:
1.) Claim/s as a result of normal wear and tear or of any modifications and / or alterations to the product in any
shape or form.
2.) Claim/s as a result of non-compliance of the assembly, service and operating instructions and/or any unfit or
improper use.
3.) Any expenses incurred in the process of making the claim.
Note: For lamps sold in Australia warranty services are provided by HELLA Australia Pty Ltd,
54-76 Southern Rd, Mentone VIC 3194. Customer Service 1800 061 729,
custservice@ha.hella.com, www.hella.com/hella-au/21.html
For general comments about Hella marine products please contact us on E-mail at techfeedback@hellamarine.com
NaviLED PRO Self Diagnostic Control
®
To ensure long term safety at sea, each BSH certified NaviLED
with a self diagnostic control.
A photometric self-test is carried out by the lamp in periodic intervals. If the light output (and
consequently the visibility) reaches a predetermined value, the lamp activates 'Service Mode'.
Service Mode is indicated by the lamp flashing at a rate of 60 flashes per minute for 15 seconds as
soon as the lamp is switched on. This will occur for 15 seconds every time the lamp is switched on
until the unit has operated for 2000 hours. After 2000 hours, the Service Mode flash rate doubles to
120 flashes per minute for 15 seconds as soon as the lamp is switched on.
To ensure the lamp meets the light output criteria of its certification, Hella marine recommends the
light module be replaced as soon as it enters Service Mode.
Service Mode should not occur earlier than after tens of thousands of hours. By regular recreational
boating standards, even with regular night sailing, this stage will hardly ever be reached.
PRO navigation lamp is equipped
®
980 703-62 / 12.18
BSH certified NaviLED
3 NM (2LT 959 940 6xx) or 5 NM (2LT 959 940 4xx) Masthead Lamp
Hella marine LED navigation lamps offer many advantages over conventional bulb lamps.
Significantly reduced power consumption, ultra long life and high tolerance to shock and vibration
make the LED lamps the ideal choice for the harsh marine environment.
The Hella marine NaviLED PRO series are precision optical instruments, tested and type approved
®
to comply with international maritime regulations. They are covered by a 5 year warranty.
Material Description Ultra heavy duty Grilamid
Minimum visible distance 3 or 5 nautical miles (depending on model)
Cable Pre-wired with 2.5m of twin core marine cable
Operating Voltage Multivolt
Voltage Protection Spike protected to +500 volts
Reverse polarity protected to -700 volts
Power Consumption < 2.5W (0.2A@ 12V / 0.1A @ 24V) for 3 NM
4W (0.33A @ 12V / 0.17A @ 24V) for 5 NM
Degree of Protection IP 67 – Completely sealed
Weight 150g (including cable)
International Approval IMO COL REG/USCG 33 CFR 183.810 3NM/5NM
Dimensions
c c a a
c a
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress
Dimensions Dimensions Dimensions
possible interference, both emission as well as susceptibility, to the limits prescribed in international
regulations.
a = 87mm / 3.43" a = 87mm / 3.43"
a = 87mm / 3.43"
b = 90mm / 3.54" b = 90mm / 3.54"
b = 90mm / 3.54"
Protection against damage due to voltage spikes
c = 57mm / 2.25" c = 57mm / 2.25"
c = 57mm / 2.25"
This lamp is protected against reverse polarity connection, positive voltage spikes up
d = 50mm / 1.97" d = 50mm / 1.97"
d = 50mm / 1.97"
to +500 volts and negative voltage spikes of up to 700 volts.
PRO
®
lens, high impact resistant shroud
®
9-33V DC
TM
c a
Dimensions
a = 87mm / 3.43"
d
d d b b
b
b = 90mm / 3.54"
c = 57mm / 2.25"
d = 50mm / 1.97"
Designed and Manufactured in New Zealand