LAZER LINK Bedienungsanleitung Seite 6

When two Lazer Links are in intercommunication,
the incoming call functions with the respective
mobiles are maintained. If you receive an incoming
call the Intercom stops and when the call ends it
returns. The other device in Intercom, which is not
receiving the call, will receive an acoustic warning
signal. If you wish to make a call, you have to
deactivate the intercom first.
INTERCOM FUNCTIONS BETWEEN TWO LAZER LINK
ACTIVATE AND DEACTIVATE INTERCOM
When both Lazer Links are in a range of less than
10 metres from one another, switched on and
paired with their respective mobiles, in order to
establish the connection in Intercom, press the
control button (A) of one of the devices for a
couple of seconds, until you hear an acoustic
signal. The intercommunication between the two
Lazer Links will be activated then. To deactivate the
intercommunication, press the control button (A) of
one of the Lazer Links for a couple seconds.
INTERCOM VOLUME ADJUSTMENT
The Lazer Links allow changing their volume level
when they are in Intercom. Each time you press the
control button (A) the volume level changes in a
cycle of three levels (low -> medium -> high -> low...)
PAIRING IN INTERcom WITH ANoTHER DEVIcE
oR ANoTHER AUDIo REcEIVER BLUETooTH
DEVIcE (LAZER BLUE oR LAZER RINGo)
Make sure that the two devices to be associated
are switched off. Press and keep the control button
(A) of the Lazer Link pressed until the LED (A1) starts
to flash in Red and Blue. Set the other Bluetooth
device in pairing mode. Then briefly press the
control button (A) of the Lazer Link once. After a
few seconds, both devices are paired and you
MEG Lazer Link bichro DEF 2.indd 6
Downloaded from www.Manualslib.com manuals search engine
can establish the intercommunication. When they
have been associated, we recommend to switch
off the Lazer Link and to switch on the other devices
(GPS, Mobile, etc), then turn the Lazer Link back on
and activate the intercom function by pressing 2
seconds on the control button (A).
When the Lazer Link is in intercommunication,
the incoming call functions with your mobile are
maintained. If you receive an incoming call the
Intercom stops and when the call ends it returns.
The other device in Intercom will receive an acoustic
warning signal. If you wish to make a call with the
Lazer Link you have to deactivate the Intercom first.
INTERCOM FUNCTIONS WITH ANOTHER DEVICE
OR ANOTHER AUDIO RECEIVER BLUETOOTH
(LAZER BLUE OR LAZER RINGO)
ACTIVATE AND DEACTIVATE INTERCOM
The Lazer Link
intercommunication
device. To establish a connection in Intercom,
the two devices should be in a range of less than
10 metres from one another, switched on and
paired. Then press the control button (A) on the
Lazer Link for a couple of seconds until you hear an
acoustic signal. The intercommunication will then
be activated. To deactivate it press and keep the
control button (A) of the Lazer Link pressed for a
couple of seconds.
INTERCOM VOLUME ADJUSTMENT
®
The Lazer Links allow changing their volume level
when they are in Intercom. Each time you press the
control button (A) the volume level changes in a
cycle of three levels (low -> medium -> high -> low...)
®
- 6 -
DEVICE
®
can activate or deactivate
with another Bluetooth
12/12/12 14:23
Bluet
Profile
Batte
7 ho
time
devic
Lazer
manu
Obse
ensu
- Do n
as t
Add
®
is da
- Kee
- Kee
hum
- Avo
cau
whe
batt
- Do
circ
- Do n
dam
func
- Do
clea