Operating Elements; Important Notes; Power Supply - Monacor International JTS MH-850/1 Bedienungsanleitung

All operating elements and connections can be
found on the fold-out page 3.

1 Operating Elements

1.1 Fig. 1: Hand-held microphone
1 Microphone cartridge; to insert batteries, unscrew
the cartridge (figs. 2 to 4)
2 Cap for the control part; remove the cap for ad -
justing the transmission channel (fig. 5)
3 LED status indication: shows
– green as a power indication
– red when the batteries are almost exhausted
4 Power switch
1.2 Figs. 2 – 4: Inserting batteries
(microphone cartridge unscrewed)
5 4-pole contact, each on the microphone cartridge
(fig. 2) and on the handle (fig. 3);
prior to assembling the microphone cartridge and
the handle, fit the contacts into each other
6 Lock for the battery holder (7);
to unlock the holder, push the lock to the rear in
arrow direction
7 Battery holder for two 1.5 V batteries of size AA (R6)
1.3 Fig. 5: Control part (cap removed)
8 Rotary switch CH for adjusting the transmission
channel with the adjusting key supplied

2 Important Notes

The wireless microphone corresponds to all relevant
directives of the EU and is therefore marked with
G
The microphone is suitable for indoor use only. Pro-
tect it against dripping water and splash water, high
air humidity, and heat (admissible ambient tempera-
ture range 0 – 40 °C).
G
For cleaning only use a dry, soft cloth; never use
chemicals or water.
G
No guarantee claims for the microphone and no lia-
bility for any resulting personal damage or material
damage will be accepted if the microphone is used
for other purposes than originally intended, if it is not
correctly operated or not repaired in an expert way.
If the microphone is to be put out of operation
definitively, take it to a local recycling plant for
a disposal which is not harmful to the envi-
ronment.
Dead batteries or defective rechargeable batteries
do not belong in the household rubbish; always take
them to a special waste disposal (e. g. collecting con-
tainer at your retailer).
6
3 Applications
Together with the receiver US-8001D/ 1 (1 receiving
unit) or US-8002D/ 1 (2 receiving units) from JTS, this
dy namic hand-held microphone with integrated UHF
PLL transmitter makes up a wireless audio trans -
mission system. The transmission channel can be
selected as desired among 16 channels in the UHF
frequency range of 863 to 865 MHz.
3.1 Conformity and
approval of the wireless microphone
Herewith, MONACOR INTERNATIONAL declare that
the wireless microphone MH-850/ 1 is in accordance
with the basic requirements and the other relevant reg-
ulations of the directive 1999 / 5 / EC. The declaration of
conformity is available on request from MONACOR
INTERNATIONAL. The wireless microphone is licence-
free and generally approved for operation in EU and
EFTA countries.

4 Power Supply

G
Only insert batteries of the same type and always
replace all batteries.
G
If the microphone is not used for a longer period
(e. g. more than a week), remove the batteries.
Thus, the microphone will not be damaged in case
of battery leakage.
1) Unscrew the microphone cartridge (1).
2) To unlock the battery holder (7), push the lock (6) to
the rear in arrow direction
3) Pull out the battery holder to the stop (fig. 4) and
insert two 1.5 V batteries of size AA (R6) with the
positive and negative connections as indicated on
the holder.
.
4) Slide back the battery holder until it locks into place.
5) Place the microphone cartridge on the handle in
such a way that the 4-pole contacts (5) of the car-
tridge and of the handle fit into each other, then
screw the cartridge on the handle.
5 Setting the Microphone into Operation
1) Before switching on the microphone, set the re -
ceiver to an interference-free transmission channel
(see instruction manual of the receiver).
2) Then switch on the microphone: Set the sliding
switch (4) to ON. The LED status indication (3)
shows green to indicate normal operation. If it
shows red after switching on or during operation,
the inserted batteries are almost exhausted and
must be replaced.
3) To adjust the transmission channel, remove the plas-
tic cap (2). For this purpose, slightly press the