Cleaning, Maintenance And Ordering Of Spare Parts; Operation - HERKULES H-NT 1815 Originalbetriebsanleitung

Assembling the dirt bag (Fig. 9)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dirt bag (14). Slip the dirt bag (14)
over the vacuuming hole. The dirt bag (14) is sui-
table for dry-vacuuming only. The dirt bag makes
it easier to dispose of the sucked-in dust.
5.3 Fitting the suction hose (Fig. 3, 10, 11)
Connect the suction hose (10) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8)
Blowing
Connect the suction hose (10) to the blow con-
nector (9)
One or more of the elements which make up the
3-part suction tube (11) can be attached to the
suction hose (10) to extend it. The adapter (17)
must be inserted between the suction tube (10)
and the combination nozzle (12) or crevice nozzle
(16).
5.4 Suction nozzles
The combination nozzle (12) with attachments is
for vacuuming solids and liquids over medium to
large areas. The crevice nozzle (16) is specially
designed for cleaning cervices and edges.

6. Operation

Important!
Switch off the equipment if liquid or foam is
emitted with the exhaust air when wet vacuum
cleaning.
6.1 On/Off switch (Fig. 1)
Switch position 0: Off
Switch position I: On
6.2 Dry vacuuming
Use the dirt bag (14) and the additional fi lter (18)
for dry vacuuming (see point 5.2).
Always ensure that the fi lters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (15) (see
point 5.2).
Check that the fi lter is securely fi tted at all times.
Anl_H_NT_1815_SPK7.indb 14 Anl_H_NT_1815_SPK7.indb 14
GB
Important!
When wet vacuuming, the fl oating safety switch
(5) turns off the wet and dry vacuum cleaner auto-
matically when the maximum level is reached.
Important!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
fi lter.
6.4 Blowing
Connect the suction hose (10) to the blow con-
nector (9) on the wet and dry vacuum cleaner.
7. Cleaning, maintenance and
ordering of spare parts
Important!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible.
•
We recommend that you clean the equipment
immediately after you use it.
7.2 Cleaning the appliance head (3)
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plas-
tic parts in the appliance.
7.3 Cleaning the container (7)
The container can be cleaned with a damp cloth
and some soft soap or under running water, de-
pending on the amount of dirt.
7.4 Cleaning the foam fi lter (15)
Clean the foam fi lter (15) with a little soft soap un-
der running water and allow it to air-dry.
7.5 Servicing
At regular intervals and before each use, check
that the fi lters in the wet and dry vacuum cleaner
are securely fi tted.
- 14 -
05.11.15 10:39 05.11.15 10:39