Manufacturer's Address; Data Protection Notice - Zeiss DTI 3/35 Gebrauchsanleitung

Replacing the lens cap
To replace the lens cap (2), unscrew the screws (3) using a screwdriver. Remove the
retaining plate (4) and the defective lens cap (2). Fit the new lens cap (2) and retaining
plate (4). Tighten the screws (3) using a screwdriver.
Care and maintenance of the device
Do not rub coarse particles (e.g. sand) from the lenses. Blow them off, or use a soft
brush! Over time, fingerprints can corrode the lens surface. Breathing on the lens
and polishing it with a clean optical cleansing cloth is the easiest method of cleaning
the lens surface.
Dry storage and keeping the outer lens surfaces well ventilated, especially in
the tropics, helps to prevent a possible mold film forming on the optics.
Your ZEISS DTI 3/35 requires no further special care.
Care and maintenance of the battery
Follow these steps to extend the battery life:
• Avoid storing the device at high temperatures.
• Avoid storing the device with a fully charged battery.
• Avoid complete discharging of the device.
Spare parts
Should you require spare parts for your device, e.g. the lens cap, please contact your
specialist retailer, your local distributor or our after-sales service.
For Customer Service inquiries we are happy to take your calls from Monday to Friday
from 8:00 a.m. to 4:30 p.m. (CET).
Tel.: +49 (0) 800 934 77 33
Fax: +49 (0) 64 41-4 83 69
service.sportsoptics@zeiss.com
(1)
(2)
(3)
(4)
ZEISS is a byword for reliability and a high level of quality. Therefore, quite
independently of the seller's warranty obligations to the customer, we
the manufacturer offer a two year warranty on this ZEISS product, which can
be extended for a further year upon registration of the product if registration is
made within four weeks of purchase.
The scope of the warranty can be seen by accessing the following link:
www.zeiss.com/cop/warranty
Register your product at: www.zeiss.com/cop/register

Manufacturer's address

Carl Zeiss AG
Carl-Zeiss-Strasse 22
D-73447 Oberkochen
www.zeiss.com/nature und www.zeiss.com/hunting
Subject to changes in design and scope of supply due to technical improvements.
No liability for mistakes and printing errors.

Data protection notice

Personal data is processed when using the DTI 3/35.
Our information on data protection and the processing of personal data can
be found in our download center: www.zeiss.com/hunting/manuals
Legal and regulatory information
Wireless transmitter module frequency range: WLAN: 2,412 - 2,462 MHz
Wireless transmitter module power: 100 mW
Carl Zeiss AG thus declares that the thermal imaging camera
DTI 3/35 complies with the directives 2014/53/EU and
2011/65/EU. The full text of the EU declaration of conformity
as well as additional information are available at:
www.zeiss.com/dti-335/conformity.
Power supply unit manufaturer
Shenzhen Simsukian Electronic Technology Co., Ltd.
Building 1, the 5th plant, Jiayi Industrial Park
Daping Community, Guanlan Street Longhua District
Shenzhen P.R. China
Model identifier: SK22G-0500200Z
TECHNICAL DATA ON POWER SUPPLY UNIT
Electronics
Input voltage VAC
Input frequency Hz
Output voltage VDC
Output current A
Power output W
Average operating efficiency %
Power consumption at zero load W
Ambient conditions
Operating temperature °C (°F)
Relative humidity rH
Storage temperatures °C (°F)
Protection type
Carl Zeiss AG
Carl-Zeiss-Strasse 22
73447 Oberkochen
Germany
www.zeiss.com/nature
www.zeiss.com/hunting
100 - 240
50 / 60
5
2
10
82.98
0.068
-0 / +40 ( -32 / +104)
25% - 90%
-30 / +60 ( -22 / +140)
IP 20
16 | 200 EN